manualshive.com logo in svg

Edge-Core ECS4810-12M, Руководство по установке, Страница: 68 / 76

Поделиться
Скачать
Edge-Core ECS4810-12M Скачать руководство пользователя страница 68

G

LOSSARY

 

–  68  –

A

UTO

-N

EGOTIATION

Signalling method allowing each node to select its optimum operational mode 
(e.g., speed and duplex mode) based on the capabilities of the node to which it 
is connected.

B

ANDWIDTH

The difference between the highest and lowest frequencies available for network 
signals. Also synonymous with wire speed, the actual speed of the data 
transmission along the cable.

C

OLLISION

 D

OMAIN

Single CSMA/CD LAN segment.

CSMA/CD

CSMA/CD (Carrier Sense Multiple Access/Collision Detect) is the communication 
method employed by Ethernet, Fast Ethernet, and Gigabit Ethernet.

E

ND

 S

TATION

A workstation, server, or other device that does not forward traffic.

E

THERNET

A network communication system developed and standardized by DEC, Intel, 
and Xerox, using baseband transmission, CSMA/CD access, logical bus topology, 
and coaxial cable. The successor IEEE 802.3 standard provides for integration 
into the OSI model and extends the physical layer and media with repeaters and 
implementations that operate on fiber, thin coax and twisted-pair cable.

F

AST

 E

THERNET

A 100 Mbps network communication system based on Ethernet and the CSMA/
CD access method.

F

ULL

 D

UPLEX

Transmission method that allows two network devices to transmit and receive 
concurrently, effectively doubling the bandwidth of that link.

Содержание ECS4810-12M













































































Отзывы:

Нет отзывов