manualshive.com logo in svg

Edge-Core ECS4810-12M, Руководство по установке, Страница: 26 / 76

Поделиться
Скачать
Edge-Core ECS4810-12M Скачать руководство пользователя страница 26

C

HAPTER

 1

  |  Introduction

Description of Hardware

–  26  –

D

ESCRIPTION

 

OF

 H

ARDWARE

SFP S

LOTS

The 12 Small Form Factor Pluggable (SFP) transceiver slots are shared with 12 
RJ-45 ports. In its default configuration, if an SFP transceiver (purchased 
separately) is installed in a slot and has a valid link on its port, the associated 
RJ-45 port is disabled and cannot be used. The switch can also be configured to 
force the use of an RJ-45 port or SFP slot, as required.

The SFP slots support the following SFP transceivers:

◆

1000 Mbps Ethernet SFP transceivers

■

1000BASE-LX5

■

1000BASE-LX15

■

1000BASE-LHX

■

1000BASE-ZX

◆

100 Mbps Ethernet SFP transceivers

■

100BASE-FX

For information on the recommended standards for fiber optic cabling, see 

"Fiber 

Optic SFP Devices" on page 46.

10/100/1000BASE-T P

ORTS

The switch contains contains 12 1000BASE-T RJ-45 ports that operate at 10 
Mbps or 100 Mbps, half or full duplex, or at 1000 Mbps, full duplex. Because all 
of the RJ-45 ports support automatic MDI/MDI-X operation, you can use 
straight-through cables for all network connections to PCs or servers, or to other 
switches or hubs. (See 

"1000BASE-T Pin Assignments" on page 60

.)

Each of these ports support auto-negotiation, so the optimum transmission 
mode (half or full duplex), and data rate (10, 100 or 1000 Mbps) can be selected 
automatically. If a device connected to one of these ports does not support auto-
negotiation, the communication mode of that port can be configured manually. 

Содержание ECS4810-12M













































































Отзывы:

Нет отзывов