Edge-Core ECS4810-12M Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 76

Edge-Core ECS4810-12M Скачать руководство пользователя страница 31

– 31 –

2

I

NSTALLING

THE

S

WITCH

S

ELECTING

A

S

ITE

Switch units can be mounted in a standard 19-inch equipment rack or on a flat
surface. Be sure to follow the guidelines below when choosing a location.

◆

The site should:

■

be at the center of all the devices you want to link and near a power
outlet.

■

be able to maintain its temperature within -25 to 60 °C (-13 to 140 °F)
and its humidity within 10% to 90%, non-condensing

■

provide adequate space (approximately two inches) on all sides for
proper air flow

■

be accessible for installing, cabling and maintaining the devices

■

allow the status LEDs to be clearly visible

◆

Make sure twisted-pair cable is always routed away from power lines,
fluorescent lighting fixtures and other sources of electrical interference,
such as radios and transmitters.

◆

Make sure that the unit is connected to a separate grounded power outlet
that provides 100 to 240 VAC, 50 to 60 Hz, is within 2 m (6.6 feet) of each
device and is powered from an independent circuit breaker. As with any
equipment, using a filter or surge suppressor is recommended.

«
...
29
30
31
32
33
...
»

Содержание ECS4810-12M













































































Отзывы:

Нет отзывов