manualshive.com logo in svg

Edge-Core ECS4810-12M, Руководство по установке, Страница: 47 / 76

Поделиться
Скачать
Edge-Core ECS4810-12M Скачать руководство пользователя страница 47

C

HAPTER

 3

  |  Making Network Connections

Fiber Optic SFP Devices

–  47  –

2.

Check that the fiber terminators are clean. You can clean the cable plugs by 
wiping them gently with a clean tissue or cotton ball moistened with a little 
ethanol. Dirty fiber terminators on fiber cables will impair the quality of the 
light transmitted through the cable and lead to degraded performance on 
the port.

3.

Connect one end of the cable to the LC port on the switch and the other end 
to the LC port on the other device. Since LC connectors are keyed, the cable 
can be attached in only one orientation.

Figure 16:  Making Connections to SFP Transceivers

4.

As a connection is made, check the Link LED on the switch corresponding to 
the port to be sure that the connection is valid.

The 1000BASE-LX5, 1000BASE-LX15, 1000BASE-LHX, and 1000BASE-ZX fiber 
optic ports operate at 1 Gbps full duplex. The maximum length for fiber optic 
cable operating at Gigabit speed will depend on the fiber type as listed under 

"1000 Mbps Gigabit Ethernet Collision Domain" on page 48

.

The 100BASE-FX fiber optic ports operate at 100 Mbps full duplex. The 
maximum length for fiber optic cable operating at 100 Mbps speed is listed 
under 

"100 Mbps Fast Ethernet Collision Domain" on page 49

.

27

Содержание ECS4810-12M













































































Отзывы:

Нет отзывов