manualshive.com logo in svg

Edge-Core ECS4810-12M, Руководство по установке, Страница: 11 / 76

Поделиться
Скачать
Edge-Core ECS4810-12M Скачать руководство пользователя страница 11

C

OMPLIANCES

 

AND

 S

AFETY

 S

TATEMENTS

–  11  –

Bitte unbedingt vor dem Einbauen des Switches die folgenden 
Sicherheitsanweisungen durchlesen:

WARNUNG:

 Die Installation und der Ausbau des Geräts darf nur durch 

Fachpersonal erfolgen.

◆

Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose 
angeschlossen werden.

◆

Das Gerät muß an eine geerdete Steckdose angeschlossen werden, welche 
die internationalen Sicherheitsnormen erfüllt.

◆

Der Gerätestecker (der Anschluß an das Gerät, nicht der 
Wandsteckdosenstecker) muß einen gemäß EN 60320/IEC 320 
konfigurierten Geräteeingang haben.

◆

Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein. 
Die Stromversorgung des Geräts kann nur durch Herausziehen des 
Gerätenetzkabels aus der Netzsteckdose unterbrochen werden.

◆

Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen 
(Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen sind 
nur gegeben, wenn auch die an das Gerät angeschlossenen Geräte unter 
SELV-Bedingungen betrieben werden.

Stromkabel

. Dies muss von dem Land, in dem es benutzt wird geprüft werden: 

Schweiz

Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen einhalten.

Europe

Das Netzkabel muß vom Typ HO3VVF3GO.75 (Mindestanforderung) 

sein und die Aufschrift <HAR> oder <BASEC> tragen.

Der Netzstecker muß die Norm CEE 7/7 erfüllen (”SCHUKO”).

Содержание ECS4810-12M













































































Отзывы:

Нет отзывов