Edge-Core ECS4810-12M Скачать руководство пользователя страница 53

Страница: 53 / 76

– 53 –

ROUBLESHOOTING

IAGNOSING

WITCH

NDICATORS

Table 14: Troubleshooting Chart

Symptom

Action

PWR LED is Off

◆

Check connections between the switch, the power cord and

the wall outlet.

◆

Contact your dealer for assistance.

Port LED is Off

◆

Verify that the switch and attached device are powered on.

◆

Be sure the cable is plugged into both the switch and

corresponding device.

◆

If the switch is installed in a rack, check the connections to

the punch-down block and patch panel.

◆

Verify that the proper cable type is used and its length does

not exceed specified limits.

◆

Check the adapter on the attached device and cable

connections for possible defects. Replace the defective

adapter or cable if necessary.

DIAG LED is Amber

◆

Power cycle the switch to try and clear the condition.

◆

If the condition does not clear, contact your local dealer for

assistance

MGMT LED is off

◆

Verify that the switch and attached device are powered on.

◆

Be sure the cable is plugged into both the switch and

corresponding device.

◆

Verify that the proper cable type is used and its length does

not exceed specified limits.

◆

Check the adapter on the attached device and cable

connections for possible defects. Replace the defective

adapter or cable if necessary.

Содержание ECS4810-12M













































































Результаты поиска

Содержание ECS4810-12M

Отзывы:

Edge-Core ECS4810-12M, Руководство по установке, Страница: 53 / 76

Результаты поиска

Содержание ECS4810-12M

Отзывы: