Edge-Core ECS4810-12M Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 76

Edge-Core ECS4810-12M Скачать руководство пользователя страница 12

C

OMPLIANCES

AND

S

AFETY

S

TATEMENTS

– 12 –

W

ARNINGS

AND

C

AUTIONARY

M

ESSAGES

E

NVIRONMENTAL

S

TATEMENTS

The manufacturer of this product endeavours to sustain an environmentally-
friendly policy throughout the entire production process. This is achieved though
the following means:

◆

Adherence to national legislation and regulations on environmental
production standards.

◆

Conservation of operational resources.

◆

Waste reduction and safe disposal of all harmful un-recyclable by-products.

◆

Recycling of all reusable waste content.

◆

Design of products to maximize recyclables at the end of the product’s life
span.

◆

Continual monitoring of safety standards.

W

ARNING

:

This product does not contain any serviceable user parts.

W

ARNING

:

Installation and removal of the unit must be carried out by

qualified personnel only.

W

ARNING

:

When connecting this device to a power outlet, connect the

field ground lead on the tri-pole power plug to a valid earth ground line
to prevent electrical hazards.

W

ARNING

:

This switch uses lasers to transmit signals over fiber optic

cable. The lasers are compliant with the requirements of a Class 1
Laser Product and are inherently eye safe in normal operation.
However, you should never look directly at a transmit port when it is
powered on.

C

AUTION

:

Wear an anti-static wrist strap or take other suitable

measures to prevent electrostatic discharge when handling this
equipment.

C

AUTION

:

Do not plug a phone jack connector in the RJ-45 port. This

may damage this device.

C

AUTION

:

Use only twisted-pair cables with RJ-45 connectors that

conform to FCC standards.

«
...
10
11
12
13
14
...
»

Содержание ECS4810-12M













































































Отзывы:

Нет отзывов