Edge-Core ECS4810-12M Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 76

Edge-Core ECS4810-12M Скачать руководство пользователя страница 23

– 23 –

1

I

NTRODUCTION

O

VERVIEW

The ECS4810-12M is an intelligent Layer 2 switch designed for aggregating
broadband traffic from the edge of a service provider’s (CO) network. It
aggregates traffic using its 12 Gigabit combination RJ-45/SFP ports, (see

Figure 2 on page 24

). The SFP ports allow the switch to receive traffic up to 2

km from the CO using 100BASE-FX fiber transceivers, or up to much greater
distances using 1000BASE-LH transceivers, giving you the option of placing the
switch either in the CO or anywhere along the path between the CO and
subscribers.

Figure 1: Deployment

The switch has a 1000BASE-T port for dedicated management access (which can
be operated outside the data channel). It has an SNMP-based management
agent embedded on the main board, which supports both in-band and out-of-
band access using a Web browser, SNMP/RMON, or Telnet.

Metropolitan
Area
Network

Access
Aggregation
Network

VPN

Internet

Packet

Telephony

Video

Central Office (CO)

EC View
Network Management System
(NMS)

Broadband
Access
Network

Broadband Access Aggregation

Edge Network

AGG-E

AGG-E

AGG-E

Network

Gateway

HOME /

OFFICE

SUBSCRIBERS

VDSL

FTTH

VDSL

FTTH

ECS4810-12M

ECS4810-12M

ECS4810-12M

«
...
21
22
23
24
25
...
»

Содержание ECS4810-12M













































































Отзывы:

Нет отзывов