manualshive.com logo in svg

ECKELMANN CI 3000, Руководство по эксплуатации

Поделиться
Скачать
ECKELMANN CI 3000 Скачать руководство пользователя страница 43

Installation and Startup of CI 3000 / SIOX

37

Version 2.09   09. April 2014

5.4

Local configuration LDS-system by service PC

For the configuration of LDS components an on-site service PC (installed with the LDSWin software) can be
connected to the CI 3000 store computer via the following routes:

S

Connection via CAN bus PC adapter

The CAN bus PC adapter designed for use with the LDS System interfaces between a service PC with the CAN bus
for communication with the LDS components. For more information on the CAN bus PC adapter see its operating
instruction.

OR

S

Connection via Combi Gateway

The Combi Gateway was designed for use within the LDS system. It forms the interface between an on-site ser­
vice PC in the local network and the CAN Bus, used for communication with the LDS components. For more
information on the Combis Gateway see its operating instruction.

OR

S

Connection via modem port of CI 3000

 

Store computer

A null modem cable (EAG No. PCZKABSER2) is required to connect the CI 3000 store computer to the serial
interface of a service PC.

If required, the modem cable must first be disconnected from the CI 3000 store computer in order to connect
the null modem cable to the interface labelled MODEM:

MODE

ESC

PRIO 1

PRIO 2

,

9

WXYZ

7

PQRS

8

TUV

6

MNO

4

GHI

5

JKL

3

DEF

2

ABC

1

0

ALARM
RESET

LDSWin

MODEM

(COM1)

MODEM

COMx

ZNR. 51203 80 130 DEF

As soon as LDSWin goes online the store computer automatically switches from the “Modem” coupling mode
to the “Direct” coupling mode.

The CI 3000 store computer is only in the ”Direct coupling mode” when the LDSWin is actually on­
line! Simply connecting the null modem cable is not sufficient!

If the CI 3000 store computer is unable to detect a modem or has not switched to the ”Direct coupling mode”,
then the alarm 

Modem fault

 is generated following the elapse of a parameterisable time period (see menu 7-4).

The 

Modem Fault

 alarm is suppressed during the time the LDSWin software is online via the null modem cable.

Failure of error message transmission! 

Automatic fault report transmission is interrupted as long

as direct cable connection is maintained. New alarm messages are then reported directly to the con­
nected Service PC. After restoring the normal state, the CI 3000 Store Computer will report all
alarms generated during direct connection to the specified destinations in the usual manner.

Содержание CI 3000







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды