manualshive.com logo in svg

ECKELMANN CI 3000, Руководство по эксплуатации

Поделиться
Скачать
ECKELMANN CI 3000 Скачать руководство пользователя страница 19

Application of CI 3000

13

Version 2.09   09. April 2014

3

Application of CI 3000

S

Centralized parameter setting and configuration

 

of all LDS components via CAN bus:

The CI 3000 Store Computer can be used for remote control and configuring of all LDS components from a sin­
gle location via CAN bus. In-use change of the user language can also be made from the central location.

S

The CI 3000 Store Computer's RS232 interface (COM2) with the RS232/RS485 Converter can be used to in­
tegrate UA 30 Rx compact controllers / Dixell controllers as well as external controllers into the LDS system.

S

CI 3100 only: UA 30 Rx compact controllers and Dixell controllers can be directly integrated in the LDS system
via the RS485 interface (COM3). The RS232 interface (COM2) is then available for the integration of external
controllers or as a BMS data interface to external systems.

S

Centralized display of operating data, messages and alarms generated by all LDS components.

S

Alarm signalling by indicator light and buzzer and by external horn and alarm contacts.

S

Monitoring of two connected external digital signals (external alarms and meter)

S

Monitoring of CAN bus and operational status of all LDS components:

Alarm is generated in fault or failure of CAN bus and failure of LDS components.

S

Centralized time synchronization (master clock):

Date and time can be set with the CI 3000 Store Computer for the complete system. The CI 3000 Store Com­
puter also performs cyclic synchronization of internal clocks in all LDS components via the CAN bus. The
CI 3000 contains a battery-backed real-time clock, which supports automatic daylight saving change.

S

Remote maintenance of the installation / store via a central computer (PC) with the PC software LDSWin.

S

Energy management:

Power, water, gas meters and heat meters with a pulse output (S0) can be connected to the CI 3000
Store Computer i.e. also the M-bus meter by means of the M-bus gateway, which then determines and 
archives current power or flow rate and the daily energy requirement or consumption.

S

Load Shedding Manager (LSM)

Load Shedding Manager can be configured for up to 20 shedding points and optimizes power input of the re­
frigeration/building control system within a load optimizing interval of 15 min.

S

Remote alarming of LDS System Alarm signal transmitted to fault indicator centre

via modem, GSM, SMS, FAX, voice message and network.

Содержание CI 3000







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды