background image

Page 8 of 12

TR Series Wiring

A TR series DuoBeam™ has a single cable with 7 colored wires. A dedicated ground wire, a dedicated power wire and five colored control 

wires which run through the main driver board.

The 16 AWG black ground wire should be connected directly to the battery. The 16 AWG red power wire requires a constant 10 to 16V(+) 

power source with a customer supplied in line 

15A

 fuse.

The five control cable wires (listed in TABLE 3 below) routed through the driver board carry only low current (30 mA average) input signals to 

control the DuoBeam™ functions and must be routed to the output of a control switch (or directly to multiple switches).

TABLE 3

Emergency Mode Flash Pattern Selection

There are seven customizable emergency flash pattern modes available based on the wire combinations shown in TABLE 4. When using 

individual switches, make sure to configure all possible switch combinations.

To change a flash pattern on a single emergency level mode:

1. Power-up the unit and apply +power to the level mode wire(s) you wish to change (see TABLE 4). The unit will flash the default pattern.

2. Momentarily touch the GRN pattern select wire to (+) power to cycle through to the next flash pattern shown on TABLE 5.

3. To reset the flash pattern to the factory default, hold the GRN pattern select wire to (+) power for ~5 seconds.

Standard TR Function Wire Definitions

Function Wire Color

Function

Description

BLU

L1

Level 1 Emergency Mode

ORG

L2

Level 2 Emergency Mode

YEL

L3

Level 3 Emergency Mode

GRN

Pattern Select

WHT

Lightbar Dim

Set LEDs to DIM mode

Notice:

 When the GRN Pattern Select wire is connected to +power alone, test mode is enabled to excercise all outputs in 

sequence.

Level Mode Combinations

Flash Pattern Modes Function Wire Color(s)

Pattern

Description

FPM

L1

BLU

1

Cycle Flash Simultaneous

70

L2

ORG

1

Cycle Flash Simultaneous

70

L3

YEL

1

Cycle Flash Simultaneous

70

L1 + L2

BLU & ORG

1

Cycle Flash Simultaneous

70

L1 + L3

BLU & YEL

1

Cycle Flash Simultaneous

70

L2 + L3

ORG & YEL

1

Cycle Flash Simultaneous

70

L1 + L2 + L3

BLU, ORG & YEL

1

Cycle Flash Simultaneous

70

TABLE 4

Содержание DuoBeam













Отзывы: