background image

 
AVA PRO - Assembly instructions for the CPX300W alarm control panel

  

6

 

/

 

23

 

5.

 

Applications with which the device works:

 

 

EBS  Config  2.0  in  the desktop  version  -  a  computer  program for  installers  used to  configure 
the system, 

 

EBS Config 2.0 in the smartphone version - a mobile application for installers used to configure 
the system, 

 

EBS Security - a mobile application for users to manage the system. 

6.

 

Inputs:

 

 

8 surge protected wire lines, 

 

TEOL configuration can be increased up to 16 wire lines, 

 

7 types of wired lines (NO / NC / EOL-NO / EOL-NC / DEOL-NO / DEOL-NC / TEOL), 

 

64 wireless lines (for wireless device data communication), 

 

15 types of reactions. 

7.

 

Outputs:

 

 

3 low-current wire outputs 100 mA rated, 

 

1 high-current wired output 1.1A current rated, 

 

7 functions. 

8.

 

Power outputs:

 

 

2 13.8 V power outputs (AUX1 +, AUX2 +), 

 

Power line rating: 350 mA, 

 

Overcurrent and overvoltage-protected 

9.

 

Users:

 

 

1 administrator, 

 

31 users, 

 

2 categories. 

10.

 

Configuration:

 

 

Local using EBS programmers, 

 

Remote via GPRS, SMS, Ethernet / Wi-Fi. 

11.

 

Programmers

:

 

 

MINI-PROG-BT

 - a programmer that allows configuration and monitoring of the control panel 

thanks to the IDC10 connector and Bluetooth technology. 

 

GD-PROG

  -  a  programmer  that  has  an  RS232  connector  to  a  computer  and  an  IDC10 

connector  for  configuring  and  monitoring  the  control  panel  status  using  the  EBS  Config  2.0 
program. 

 

SP-PROG

 - a programmer in two variants: 

o

 

SP-PROG,  having  an  RS232  connector  for  connection  to  a  computer  and  USB  for 
configuring and monitoring the control panel status using the EBS Config 2.0 program. 

o

 

SP-PROG-BT, having a micro USB connector, RS232 and a built-in Bluetooth module. For 
cable  connection,  the  situation  is  the  same  as  for  SP-PROG.  For  Bluetooth  technology, 
both  at  the

  Configuration  port

  and  the 

Information  port

  position,  the  same  port  for 

communication must be set. 

12.

 

Additional information:

 

 

4 partitions 

 

1 keypad is used to manage 1 partition, 

 

Up to 8 KP3W keypad can be added to the system, 

 

Multiple keyboards can be added to 1 partition, 

 

Up to 8 PIR-CAM-30 motion detectors with camera can be added to the system, 

 

Up to 8 BM8000PLx-C3W wireless siren can be added to the system, 

Содержание AVA PRO CPX300W
























Отзывы: