manualshive.com logo in svg

Eaton UltraShift PLUS FO(M) E310C-LAS Series, Инструкция по эксплуатации, Страница: 21 / 44

Поделиться
Скачать
Eaton UltraShift PLUS FO(M) E310C-LAS Series Скачать руководство пользователя страница 21

16

Operation

2. Re-select Primary Configuration Settings

•

Press and hold the Downshift button for 4 seconds.

Note: 

The gear display will display “C1” on the gear display for 3 seconds indi-

cating the transmission Primary Configuration settings have been 
reselected. 

Eaton Push Button

Note: 

Not all Eaton Push Button controllers have Configuration Switch capa-

bility.

1. Select Secondary Configuration Settings

•

Press and release the Configuration button on the Eaton Push Button 
controller.

Note: 

The gear display will display “C2” on the gear display every 15 seconds 

indicating the transmission is using the Secondary Configuration 
settings.

2. Re-select Primary Configuration Settings

•

Press and release the Configuration button on the Eaton Push Button 
controller.

Note: 

The gear display will display “C1” on the gear display for 3 seconds indi-

cating the transmission Primary Configuration settings have been 
reselected. 

OEM Switch

Note: 

Not all vehicles have an OEM momentary Configuration Switch. There 

may be a number of different OEM installed momentary Configuration 
Switches depending on your vehicle make and model. Contact your vehi-
cle manufacturer for specific details.

Содержание UltraShift PLUS FO(M) E310C-LAS Series













































Отзывы:

Нет отзывов