manualshive.com logo in svg

Eaton UltraShift PLUS FO(M) E310C-LAS Series, Инструкция по эксплуатации

Поделиться
Скачать
Eaton UltraShift PLUS FO(M) E310C-LAS Series Скачать руководство пользователя страница 11

6

Operation

Drive Mode

•

Automatically selects the start gear (see Note*). The selected start 
gear will vary depending on several vehicle inputs like load, grade, 
and axle/transmission ratio. This start gear can be changed by using 
the up/down buttons, as long as the selection still falls into a gear 
that would allow the vehicle to launch without allowing the transmis-
sion to obtain damage. 

•

If the start gear is changed using the up/down buttons, it will remain 
as the default until the vehicle is powered down or the selection is 
changed with the buttons again.

•

Automatically performs all upshifts and downshifts in all gears 
except 1st (Only on the UltraShift 

PLUS

 Vocational Multipurpose 

Series (VMS) models) and Reverse on all models.

•

A shift can be advanced by pressing the up/down buttons when the 
transmission is near the shift point.

•

The transmission may also deny a shift while ascending or descend-
ing grades if the load of the vehicle, and grade of the terrain in com-
bination with the drivetrain ratio and engine torque will fall outside of 
the acceptable range to perform a shift. If the shift is denied it will 
sound a tone.

Note: 

Multiple gear upshifts and downshifts may be allowed when the shift 

buttons are pushed multiple times (Each button push equals one gear 
change request).

Important: 

Prior to ascending a steep grade the driver should reduce default 

start gear by one or ensure full throttle is applied for the duration of the grade 
so the vehicle maintains the proper engine and vehicle speed during the entire 
grade. Driver can button down by using the down arrow on the shift lever.

Note: 

*If the driver attempts to select a non-neutral mode without depressing 

the service brakes the transmission will not shift into gear and the driver 
will have to return to Neutral and depress the brakes before selecting the 
desired mode again.

Important:

 If the driver depresses and holds both pedals (even if done acci-

dentally) the launch will be abrupt and the engine and brake forces may rock 
and bounce the vehicle. Releasing either pedal will stop this immediately.

!

!

Содержание UltraShift PLUS FO(M) E310C-LAS Series













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды