Eaton PowerXL DF1 Series, Руководство пользователя

Страница: 53 / 284

53
5. Parameter Description
Eaton Electric General Inverters DF1 Series UMXXXXXXXXE February 2020 www.eaton.com
5.1.2 Parameter restoration
• Restore the parameters to the default values.
Parameter restoration
1: 00-02 is set to1, and the screen will display after writing, the abnormal record will be erased, 00-02 is
restoered to 0.
2: 00-02 is set to 1, and the screen will display
, the inverter will be reset.00-02 is restoered to 0.After resetting
the inverter, the values of the two relays, “electronic thermal relay” and “IGBT module thermal relay”will be set to zero.
3: 00-02is set to3, and the screen will display
, all the parameters will be restored to the default values except
the parameters in the table 1 below.After parameters are restored, 00-02 is restored to0.
Exception The parameters in table 1 below will not be restored to the default values:
Parameter Name
Factory
Value
Setting Range Content
00-02
P.996
~
P.999
Parameter restoration 0
0 No function.
1 Alarm history clear (P.996=1)
2 Inverter reset (P.997=1)
3 Restoring all parameters to default values (P.998=1)
4 Restoring some parameters to default values1 (P.999=1)
5 Restoring some parameters to default values2 (P.999=2)
6 Restoring some parameters to default values3 (P.999=3)
Group No. Name Group No. Name
00-00 P.90 The inverter model 06-58 P.754 E1 alarm output voltage
00-01 P.188 Firmware version
06-59 P.755
E1 alarm the temperature rising
accumulation rate
00-24 P.189 50Hz/60Hz switch selection
01-08 P.21 Accelerate/Decelerate time increments 06-60 P.756 E1 alarm PN voltage
06-27 P.292
Accumulative motor operation time
(minutes)
06-61 P.757 E1 alarm the time of the inverter has run
06-62 P.758 E1 alarm the inverter operation status code
06-28 P.293 Accumulative motor operation time (days) 06-63 P.759 E1 alarm (years/months)
06-29 P.296 Accumulative motor power time (minutes) 06-64 P.760 E1 alarm (days/hours)
06-30 P.297 Accumulative motor power time (days) 06-65 P.761 E1 alarm (minutes/seconds)
06-44 P.740 E1 06-70 P.766 E2 alarm output frequency
06-45 P.741 E2 06-71 P.767 E2 alarm output current
06-46 P.742 E3 06-72 P.768 E2 alarm output voltage
06-47 P.743 E4
06-73 P.769
E2 alarm the temperature rising
accumulation rate
06-48 P.744 E5
06-49 P.745 E6 06-74 P.770 E2 alarm PN voltage
06-50 P.746 E7 06-75 P.771 E2 alarm the time of inverter has run
06-51 P.747 E8 06-76 P.772 E2 alarm the inverter operation status code
06-52 P.748 E9 06-77 P.773 E2 alarm (years/months)
06-53 P.749 E10 06-78 P.774 E2 alarm (days/hours)
06-54 P.750 E11 06-79 P.775 E2 alarm (minutes/seconds)
06-55 P.751 E12 09-13 P.124 Expansion card version
06-56 P.752 E1 alarm output frequency 13-02 P.285 Low frequency vibration inhibition factor
06-57 P.753 E1 alarm output current 13-03 P.286 High frequency vibration inhibition factor