Eaton Power Xpert 9395P 250 kVA Скачать руководство пользователя страница 167

Страница: 167 / 170

158

12 Installation checklist

All packing materials and restraints have been removed from each cabinet.

Each cabinet in the UPS system is placed in its installed location.

A cabinet grounding/mounting kit is installed between any cabinets that are bolted together.

All conduits and cables are properly routed to the UPS and any ancillary cabinets.

All power cables are properly sized and terminated.

Neutral conductors are installed or bonded to ground as per requirements.

Battery cables are terminated on E4 (+) and E5 (–).

Battery Shunt trip and Aux contact signal wiring is connected from the UPS to the battery breaker.

LAN and telephone drops are installed.

All telephone and LAN connections have been completed.

A ground conductor is properly installed.

Air conditioning equipment is installed and operating correctly.

The area around the installed UPS system is clean and dust-free. (It is recommended that the UPS be installed
on a level floor suitable for computer or electronic equipment.)

Adequate workspace exists around the UPS and other cabinets.

Adequate lighting is provided around all UPS equipment.

A 230 Vac service outlet is located within 7.5 meters of the UPS equipment.

The Remote Emergency Power-off (REPO) device is mounted in its installed location and its wiring is termi-
nated inside the UPS cabinet.

The normally-closed (NC) Emergency Power-off contact (pins 1 and 2 on TB1) is jumpered if not used.

Alarm relays and building alarms are wired appropriately. (OPTIONAL)

A remote battery disconnect control is mounted in its installed location and its wiring is terminated inside the
UPS and battery cabinet. (OPTIONAL)

Accessories are mounted in installed locations and wiring is terminated inside the UPS cabinet. (OPTIONAL)

The debris shield covering the UPS cabinet ventilation grill is removed.

Startup and operational checks are performed by an authorized Eaton Customer Service Engineer.

9395P 250 kVA / 275 kVA / 300 kVA

User’s and Installation Guide

Содержание Power Xpert 9395P 250 kVA











































































































































































Результаты поиска

Содержание Power Xpert 9395P 250 kVA

Отзывы:

Похожие инструкции для Power Xpert 9395P 250 kVA

Бренды по названию

Популярные бренды

Eaton Power Xpert 9395P 250 kVA, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание Power Xpert 9395P 250 kVA

Отзывы:

Похожие инструкции для Power Xpert 9395P 250 kVA

Бренды по названию

Популярные бренды