4
OnGuard Command Console
Installation Manual
ONGUARD COMMAND CONSOLE INSTALLATION MANUAL
www.eaton.com/onguard
Important Safety Instructions
DANGER Read all instructions before assembling and using this furnishing - Save these instructions
15� Ensure that the floor is able to withstand the weight of the
console when fully loaded�
16� Ensure the console is plumb and level for proper operation�
Route all power cords and cabling as instructed, away from
any possible pinch points or moving parts�
17� To reduce risk of personal injury and product damage, always
ensure a sufficient amount of personnel are present when
unpacking, moving and assembling the console system�
Failure to adhere to these warnings may result in serious
injury or property damage.
DANGER
Electrical Ratings
Lift motor controller:
90 – 240V AC, 48Hz – 63Hz (universal)
Console Capacities
Dynamic load capacity of height adjustable lift motors:
1,000 lb�
Work surface capacity:
520 lbs�
Base cabinet flush drawer capacity:
Large drawer: 50 lbs�
Small drawer: 40 lbs�
Base cabinet roll-out shelf capacity:
60 lbs�
Monitor pole capacity:
60 lbs� each
Power distribution strips:
20 amps 120V AC (2 circuits)
Personal Environment System accessory outlets:
3 amp ea�
Optional Personal Environment System:
115V AC, 60Hz
WARNING
Do not apply loads that exceed the capacity of the console�
The applied load includes any items installed or placed onto the
console worksurface or into the base cabinet compartments after
receipt of the console from the carrier� Applied loads include (but
Console Environment
CAUTION
TO ENSURE ADEQUATE AIR FLOW TO COOL STORED
ELECTRONIC DEVICES, DO NOT LOCATE THE BACK OF THE
CONSOLE CLOSER THAN 3” TO ANY WALL, OR SIMILAR
OBSTRUCTION. DO NOT PLACE ANY OBSTRUCTION NEAR
ANY COOLING PERFORATIONS.
EACH OF THE THREE BASE CABINETS (LH, RH AND CENTER)
HAS A 650 WATT MAXIMUM COOLING
CAPACITY� WHEN ADEQUATE AIR FLOW
IS PROVIDED, THE TEMPERATURE RISE
WITHIN THE COMPARTMENT WILL BE
NO GREATER THAN 25 DEGREES (F)
(14° C)�are not limited to) monitor poles,
electronic equipment, power distribution
units, cabling, Personal Environment
System, and personal items�
DANGER
DANGER
– To reduce the risk of electric shock: This console
includes two power cords� Always fully unplug this console from
the electrical outlets before cleaning, testing, repairing or moving
the console�
WARNING
1� This console is for commercial use only�
2� Unplug from outlet before putting on or taking off parts� NOTE:
This console includes two power cords�
3� Close supervision is necessary when this furnishing is used by,
or near children, invalids, or disabled persons�
4� Use this furnishing only for its intended use as described in
these instructions� Do not use attachments not recommended
by the manufacturer�
5� Never operate this furnishing if it has a damaged cord or plug,
if it is not working properly, if it has been dropped or damaged,
or has become wet� Return the furnishing to a service center
for examination and repair�
6� Keep the cord(s) away from heated surfaces�
7� Never operate the furnishing with the air openings blocked�
Keep the air openings free of lint, hair, and the like�
8� Never drop or insert any object into any opening�
9� Do not use outdoors�
10� To disconnect, turn all controls to the off position, then remove
plugs from outlets�
11� WARNING: Risk of Electric Shock – Connect this furnishing to
properly grounded outlets only� See grounding instructions�
12� To reduce risk of electrical shock, this furnishing has polarized
plugs (one blade wider than the other)� These plugs will fit into
polarized outlets only one way� If a plug does not fit fully into
the outlet, reverse the plug� If it still does not fit, contact a
qualified electrician to install the proper outlet� Do not change
the plug in any way�
13� DO NOT, UNDER ANY CIRCUMSTANCE, PLACE
A BODY PART IN THE PATH OF THE
WORKSURFACE WHILE IT IS BEING
LOWERED�
DO NOT PLACE ANY OBJECT ON TOP OF THE
CONSOLE’S SUPPORT BASE THAT COULD INTERFERE WITH
THE TRAVEL OF THE WORKSURFACE�
This console has an electrically driven adjustable worksurface� In its
lowest position, the worksurface is very close to the support base
structure� The console’s lift motors have sensors that will detect
an obstruction when moving downward� When an obstruction is
sensed, the worksurface will automatically begin to raise�
14� Installation and assembly must be performed by qualified
personnel�