manualshive.com logo in svg

Eaton OnGuard, Руководство по установке, Страница: 20 / 24

Поделиться
Скачать
Eaton OnGuard Скачать руководство пользователя страница 20

20

ONGUARD COMMAND CONSOLE INSTALLATION MANUAL

         www.eaton.com/onguard

OnGuard Command Console

Installation Manual

SECTION IV - Accessories

D. Task Light Bracket 

This accessory is intended for use with the following 
furnishing components:

•

  OnGuard Command Console Monitor Pole: 

•

  Revo LED Light #TOALTASREVD AND #TOALTASREVDS 

with #TOALTASREVSM Surface Mounting Bracket

•

  Trillium LED Light #TOALTLED

Task Lights will be shipped in separate carton(s), along 
with their associated hardware, parts and installation guide�  
Carefully un-pack the lights from the carton(s)�

WARNING

•

   RISK OF ELECTRIC SHOCK – CONNECT THE TASK LIGHT 

(LUMINAIRE) TO A PROPERLY GROUNDED OUTLET ONLY.

•

   DO NOT ALLOW THE TASK LIGHT CORD OR 

COMBUSTIBLES SUCH AS PLASTIC, PAPER GOODS, AND 

SIMILAR MATERIALS TO COME IN CONTACT WITH THE 

LAMP, LAMP HOLDER AND REFLECTOR.

•

 

 WITH  RESPECT TO THE  COMMAND  CONSOLE’S TASK 

LIGHT BRACKET ACCESSORY, THE ABOVE LISTED 

LUMINAIRES ARE INTENDED FOR USAGE ONLY AS 

INSTRUCTED BELOW. THEY ARE NOT INTENDED FOR 

ILLUMINATION OF AQUARIUMS OR FOR INSTALLATION IN 

PLASTIC CABINETS.

To attach the bracket to the front or 

sides of the monitor pole:
1�   Remove the monitor pole’s top 

cap�

2�   Install (2) 1/4-20 x ½" Allen head 

screws into the bracket as 

shown� Partially thread (2) 1/4" 

lock nuts onto the screws�

3�   Slide the nuts down into the 

pole’s “T” channel to the 

desired height, then tighten the 

(2) screws with the provided 

Allen wrench� Replace the 

pole’s top cap�

To attach a Trillium style light 

to the bracket:
1�   Attach the task light 

support sleeve and two 

washers to the bracket 

with a 1/4 x 1" Allen head 

screw and a 1/4" lock nut�

2�   The light’s support stud 

can now be inserted into 

the sleeve� Follow the 

instructions provided 

with the Trillium light to 

complete the assembly�

To attach the bracket to the rear of 

the monitor pole:
1�   Remove the monitor pole’s top 

cap�

2�   Install (2) 1/4 x ½" Allen head 

screws into the bracket, partially 

threading them into the clamp 

plate as shown�

3�   Slide the assembly down into 

the pole’s rear channel to the 

desired height, then tighten the 

(2) screws with the provided 

Allen wrench� Replace the 

pole’s top cap�

To attach a Revo style light to 

the bracket:
1�   Remove the (3) flat head 

screws from the Revo 

surface mount bracket to 

dis-assemble the light’s 

cylindrical base�

2�   Re-attach the base to the 

Console’s Task Light 

Bracket with the (3) screws�

3�   Follow the instructions 

provided with the Revo 

light to complete the 

assembly�

Task Light Bracket Assembly

The task Light Bracket can be attached to any side of the monitor pole�  

NOTICE

PLACE ALL SEPARATELY PACKED ACCESSORY 

INSTRUCTIONS AND INSTALLATION GUIDES INTO 

THE COMPLETED CONSOLE SO THAT THEY WILL BE 

AVAILABLE TO THE END USER OF THE CONSOLE�

Description #

Part #

20" Monitor mounting column & base plate kit

KONWLC20B

3

0" Monitor mounting column & base plate kit

KONWLC30B

Pitch/pivot column head kit

KONWLK0B

Dynamic height adjustable column arm kit

KONWLK1B

Articulating

 column arm kit

KONWLK2B

Articulating

 dual monitor array column arm kit

KONWLK2DUOB

Large universal interface bracket

TOACJSBUB

Содержание OnGuard

























Отзывы:

Нет отзывов