Eaton IBC-L, Инструкции по установке

Страница: 66 / 86

58 Eaton 93PM Integrated Battery Cabinet (IBC-L, IBC-LH [432V], and IBC-LH [480V]) Installation Manual 164000228—Rev 08
NOTE In multiple IBC installations, route the battery interface wiring between IBCs through the
top of the adjacent IBC using the top inter-cabinet access pass-through (see
Figure 15 ).
2. Line-Up-and-Match Wiring. Route the battery shunt trip interface wiring from the UPS battery shunt trip
interface terminals through the bottom inter-cabinet access pass-through (see Figure 15 ) of the UPS
cabinet and IBC to the IBC battery interface terminal block TB2. See Figure 27 or Figure 28 for terminal
locations. See paragraph 3.2.2 IBC Power Wiring Preparation , Table 10 or Table 11 , and Figure 29 for
wiring and termination requirements. Refer to the applicable Eaton 93PM UPS Installation and Operation
manual listed in paragraph
1.7 For More Information , for UPS cabinet terminal locations.
3. Proceed to Step 9 .
4. Top Entry Wiring. Remove the top conduit plate (see Figure 25 ) from the top of the IBC sidecar. Identify
all conduit requirements and mark their location. Drill and punch all conduit holes in the top conduit plate
prior to mounting on the IBC. Install the conduit plate and install all conduit runs into the plate. Pull the
wiring through the conduit into the wiring area.
NOTE In multiple IBC installations, route the battery interface wiring between IBCs through the
top of the adjacent IBC using the top inter-cabinet access pass-through (see
Figure 15 ).
5. Route the battery shunt trip interface wiring from the UPS battery shunt trip interface terminals through
the top of the IBC sidecar and the top IBC inter-cabinet wiring access pass-through (see
Figure 15 ) to the
IBC battery interface terminal block TB3.
6. Proceed to Step 9 .
7. Bottom Entry Wiring. Remove the bottom conduit plate (see Figure 24 ) from the inside bottom of the
IBC. Identify all conduit requirements and mark their location. Drill and punch all conduit holes in the
bottom conduit plate prior to mounting on the IBC. Install the conduit plate and install all conduit runs into
the plate. Pull the wiring through the conduit into the wiring areas.
NOTE In multiple IBC installations, route the battery interface wiring between IBCs through the
top of the adjacent IBC using the top inter-cabinet access pass-through (see
Figure 15 ).
8. Route the battery shunt trip interface wiring from the UPS battery shunt trip interface terminals through
the bottom of the IBC to the IBC battery interface terminal block TB2.
9. Connect the battery shunt trip interface wiring to the IBC battery shunt trip interface terminals. See
paragraph
3.2.2 IBC Power Wiring Preparation and Table 12 for termination requirements.
For a detailed view of the IBC terminal block, see Figure 30 or Figure 31 .
10. Connect the battery shunt trip interface wiring to the UPS battery shunt trip interface terminals. Refer to
the applicable Eaton 93PM UPS Installation and Operation manual listed in paragraph
1.7 For More Information , for UPS cabinet termination requirements.
NOTE In the following step, if the safety shield cannot be reinstalled because of misalignment,
use the leveling feet to realign the cabinet.
11. Reinstall the internal safety shield panel removed in Step 3 of paragraph
4.3.1 Line-Up-and-Match Power Wiring .
12. Close the outside door and secure the latch.
13. If removed, reinstall the sidecar internal safety shield panel and secure with the retained hardware.
14. If removed, reinstall the sidecar front panel and secure with the retained hardware.
15. Once the battery cabinets are installed and wired, return to the applicable Eaton 93PM UPS Installation and
Operation manual, listed in paragraph 1.7 For More Information , to complete the UPS wiring.
Installation