Eaton IBC-L Скачать руководство пользователя

Страница: 82 / 86

Eaton 93PM Integrated Battery Cabinet (IBC-L, IBC-LH [432V], and IBC-LH [480V]) Installation Manual 164000228—Rev 08

77..22..22

EEnnvviirroonnm

meennttaall aanndd S

Saaffeettyy S

Sppeecciiffiiccaattiioonnss

Operating Temperature

The battery cabinet is rated for operation in up to a 40°C (104°F) ambient
temperature.

NOTE

Emergency lighting and power equipment battery cabinets (UL924) are rated
for operation in a 20°–30°C (68°–86°F) temperature environment.

The batteries are rated for a 25°C (77°F) ambient temperature to extend their useful
life.

Transit Temperature

-15°C to 40°C (5°F to 104°F)

Storage Temperature

IBC-L: -15°C to 40°C (5°F to 104°F)
IBC-LH: -15°C to 40°C (5°F to 104°F)

Operating Altitude

Maximum 1500m (5000 ft) at 40°C without derating

Transit Altitude

15000m (49213 ft)

Ventilation

Convection

Relative Humidity (operating and
storage)

95%, noncondensing

Acoustical Noise

Not applicable

Safety Conformance

UL1778 4

edition

Agency Markings

cULus

EMC (Class A)

FCC Part 15 Class A and 62040-2 c3

Product Specifications

Содержание IBC-L























































































Результаты поиска

Содержание IBC-L

Отзывы:

Похожие инструкции для IBC-L

Бренды по названию

Популярные бренды

Eaton IBC-L, Инструкции по установке

Результаты поиска

Содержание IBC-L

Отзывы:

Похожие инструкции для IBC-L

Бренды по названию

Популярные бренды