background image

32

Crash Damage

If there are signs of smoke or overheating, DO NOT go near the battery or

equipment until it has been observed from a safe distance for at least 15

minutes. Once it is safe, remove the battery and check for damage. Dispose of

damaged batteries appropriately.

Swollen Batteries

Immediately stop using or charging a battery showing any signs of swelling or

becoming too warm. If the battery is not warm to the touch, move it to an open

safe area and observe it for at least 15 minutes. Be VERY CAREFUL when

moving the batteries. Do NOT put ANY pressure on the batteries or covering

as this may cause fire.

Additional Information and Guidelines

1. Battery temperature is the best indicator for safety. The E-flite LiPo battery’s

temperature should never drop below 32 degrees Fahrenheit or go above 130

degrees Fahrenheit while charging or discharging.

2. Changing plugs or connectors is not recommended as the process is

dangerous and any error can cause fire due to shorts, reverse polarity or other

improper handling which can cause battery damage.

3. Batteries should be stored in a vented, fire resistant container. Each pack

should be stored in its own locked plastic bag within the container. The

number of packs per container should be extremely limited to avoid chain

reactions. Storage temperatures should not fall below 32 degrees Fahrenheit or

above 130 degrees Fahrenheit. Damaged batteries must be kept at even more

ambient temperatures. High temperatures may cause fire even with

undamaged batteries.

Battery Disposal

LiPo batteries require special handling for safe disposal. The following are

basic instructions for safe disposal. For more detailed safety, disposal and

recycling please go to: www.rbrc.org or www.earth911.org.

Basic Disposal Instructions

Before discarding any LiPo battery it must be rendered safe. The following

steps must be taken to avoid damage or injury to yourself, your property and

anyone who comes in contact with the battery.

If the battery is undamaged but no longer useful:

1. Discharge the battery to a maximum of 2.5V using a slow, safe discharge

method.

2. Leave battery discharged and retest after 24 hours. Many batteries

experience ‘rebound’ and may measure more than 2.5V after 24 hours. If the

voltage is greater than 2.5, repeat the procedure until the battery measures

2.5V or less.

3. Insulate each wire lead with electrical tape or other suitable material.

4. Assure that wire leads cannot touch each other by taping them to opposite

sides of the battery.

5. Place battery in a sealed plastic bag and place bag in a sealed, vented,

fire-safe container.

6. Use fire-safe container to deliver battery to a recycling center authorized for

Lithium Polymer batteries. Please note that not all battery recycling services

include LiPo’s. If no LiPo recycling facility is available in your area, contact your

local or state Hazmat agencies for instructions.

7. If the battery or wiring is damaged, please contact your local or state

Hazmat facilities for instructions. Batteries must be rendered safe before being

transported or recycled. Do NOT transport or ship batteries which have more

than a 2.5V charge OR that show signs of damage without following the

instructions given by authorities. Damaged batteries should be rendered as

safe as possible and stored in a vented fireproof container until recycled.

Instructions for Disposal of WEEE by Users in the European Union

This product must not be disposed of with other waste. Instead, it is the users

responsibility to dispose of their waste equipment by handing it over to a

designated collection point for the recycling of waste electrical and electronic

equipment. The separate collection and recycling of your waste equipment at

the time of disposal will help to conserve natural resources and ensure that it is

recycled in a manner that protects human health and the environment. For

more information about where you can drop off your waste equipment for

recyclying, please contact your local city office, your household waste disposal

service or where you purchased the product.

Содержание Pulse XT 25e ARF





































Отзывы: