background image

20

E-flite Alpha Sport 450 PNP Assembly Manual

daily flight Checks

  1. Check the battery voltage of the transmitter 

battery. Do not fly below the manufacturer’s 

recommended voltage. To do so can crash  

your aircraft.

When you check these batteries, ensure that you have 

the polarities correct on your expanded scale voltmeter.

  2. Check all hardware (linkages, screws, nuts, 

and bolts) prior to each day’s flight. Be sure that 

binding does not occur and that all parts are 

properly secured.

  3. Ensure that all surfaces are moving in the  

proper manner.

  4. Perform a ground range check before each 

day’s flying session.

  5. Prior to starting your aircraft, turn off your 

transmitter, then turn it back on. Do this each time 

you start your aircraft. If any critical switches are 

on without your knowledge, the transmitter alarm 

will sound a warning at this time.

  6. Check that all trim levers are in the  

proper location.

  7. All servo pigtails and switch harness plugs 

should be secured in the receiver. Make sure that 

the switch harness moves freely in both directions.

Warranty Information

WARRANTy PERIOd

Exclusive Warranty- Horizon Hobby, Inc., (Horizon) 

warranties that the Products purchased (the “Product”) 

will be free from defects in materials and workmanship 

at the date of purchase by the Purchaser. 

LIMITEd WARRANTy

(a) This warranty is limited to the original Purchaser 

(“Purchaser”) and is not transferable. REPAIR 

OR REPLACEMENT AS PROVIDED UNDER THIS 

WARRANTY IS THE EXCLUSIVE REMEDY OF THE 

PURCHASER. This warranty covers only those Products 

purchased from an authorized Horizon dealer. Third 

party transactions are not covered by this warranty. 

Proof of purchase is required for warranty claims. 

Further, Horizon reserves the right to change or modify 

this warranty without notice and disclaims all other 

warranties, express or implied. 

(b) Limitations- HORIZON MAKES NO WARRANTY 

OR REPRESENTATION, EXPRESS OR IMPLIED, 

ABOUT NON-INFRINGEMENT, MERCHANTABILITY 

OR FITNESS FOR A PARTICULAR PURPOSE OF THE 

PRODUCT. THE PURCHASER ACKNOWLEDGES 

THAT THEY ALONE HAVE DETERMINED THAT THE 

PRODUCT WILL SUITABLY MEET THE REQUIREMENTS 

OF THE PURCHASER’S INTENDED USE.

(c) Purchaser Remedy- Horizon’s sole obligation 

hereunder shall be that Horizon will, at its option, 

(i) repair or (ii) replace, any Product determined 

by Horizon to be defective. In the event of a defect, 

these are the Purchaser’s exclusive remedies. Horizon 

reserves the right to inspect any and all equipment 

involved in a warranty claim. Repair or replacement 

decisions are at the sole discretion of Horizon. 

This warranty does not cover cosmetic damage or 

damage due to acts of God, accident, misuse, abuse, 

negligence, commercial use, or modification of or 

to any part of the Product. This warranty does not 

cover damage due to improper installation, operation, 

maintenance, or attempted repair by anyone other 

than Horizon. Return of any goods by Purchaser must 

be approved in writing by Horizon before shipment.

dAMAGE LIMITS

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, 

INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS 

OF PROFITS OR PRODUCTION OR COMMERCIAL 

LOSS IN ANY WAY CONNECTED WITH THE 

PRODUCT, WHETHER SUCH CLAIM IS BASED IN 

CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT 

LIABILITY. Further, in no event shall the liability of 

Horizon exceed the individual price of the Product on 

which liability is asserted. As Horizon has no control 

over use, setup, final assembly, modification or misuse, 

no liability shall be assumed nor accepted for any 

resulting damage or injury. By the act of use, setup or 

assembly, the user accepts all resulting liability.

If you as the Purchaser or user are not prepared 

to accept the liability associated with the use of 

this Product, you are advised to return this Product 

immediately in new and unused condition to the place 

of purchase.

Law: These Terms are governed by Illinois law (without 

regard to conflict of law principles). 

SAfETy PRECAUTIONS

This is a sophisticated hobby Product and not a toy. 

It must be operated with caution and common sense 

and requires some basic mechanical ability. Failure to 

operate this Product in a safe and responsible manner 

could result in injury or damage to the Product or 

other property. This Product is not intended for use by 

children without direct adult supervision. The Product 

manual contains instructions for safety, operation and 

maintenance. It is essential to read and follow all 

the instructions and warnings in the manual, prior to 

assembly, setup or use, in order to operate correctly 

and avoid damage or injury.

Содержание Alpha Sport 450 PNP

























Отзывы: