E-FLITE Alpha Sport 450 PNP Скачать руководство пользователя

Страница: 3 / 24

E-flite Alpha Sport 450 PNP Assembly Manual

Recommended Radio Equipment

You will need a minimum of a 4-channel transmitter

and receiver. You can choose to purchase a complete

radio system. If you are using an existing transmitter,

just purchase the receiver separately. We recommend

the crystal-free, interference-free Spektrum

™

DX5e

2.4GHz DSM

5-channel system.

If you own a Spektrum radio, just add a DSM2

™

receiver. We show the installation of the AR500

receiver in the manual.

Complete Radio System

SPM5500

DX5e 5-Channel Full Range

w/o Servos

Or Purchase Separately

SPMAR500

AR500 5-Channel Receiver

Optional Accessories

EFLA110

Power Meter

EFLC3005

Celectra

™

1- to 3-Cell

Li-Po Charger

EFLC505

Intelligent 1- to 5-Cell

Balancing Charger

EFLSP175

-inch Aluminum Spinner

APC10070E

10x7 Electric Prop

Replacement Electronics

EFLM1400

Park 450 Brushless

Outrunner Motor, 890Kv

EFLA325A

25-Amp Airplane

Brushless ESC

EFLRS75

Sub-Micro S75 Servo

EFLRYH3

3-inch Y-harness, Lightweight

EFLREX3L

3-inch Extension, Lightweight

Replacement Propeller

EFLP1070

10x7 Slow Flyer Propeller

Battery Requirements

EFLB18003S

1800mAh 3S 11.1V 20C Li-Po,

13AWG EC3

THP21003SPL2

2100mAh 3S 11.1V 20C Li-Po,

16AWG

Required Tools and Adhesives

Tools & Equipment

Scissors

Ruler (EFLA264)

Nut driver: 5.5mm

Hex Wrench or Ball Driver: 3/32-inch, 5/64-inch

Phillips Screwdriver: #0, #1, #2 (EFLA257 and

EFLA258)

Adhesives

Clear tape

Threadlock

Optional Tools and Adhesives

Paper towel

Epoxy mixing cup

Epoxy mixing stick Epoxy brush

Rubbing alcohol

6-minute Epoxy (HAN8000)

Propeller reamer

Drill

Low tack tape

Drill bit: 3/8-inch (9.5mm)

Adjustable wrench or 10mm open-end wrench

Note on Lithium Polymer Batteries

Lithium Polymer batteries are significantly

more volatile than alkaline or Ni-Cd/

Ni-MH batteries used in RC applications.

All manufacturer’s instructions and warnings

must be followed closely. Mishandling of

Li-Po batteries can result in fire. Always

follow the manufacturer’s instructions when

disposing of Lithium Polymer batteries.

Warning

An RC aircraft is not a toy! If misused, it can cause

serious bodily harm and damage to property. Fly

only in open areas, preferably at AMA (Academy of

Model Aeronautics) approved flying sites, following all

instructions included with your radio.

Keep loose items that can get entangled in the

propeller away from the prop, including loose clothing,

or other objects such as pencils and screwdrivers.

Especially keep your hands away from the propeller.

During the course of building your model, we suggest

that you use a soft base for the building surface.

Such things as a foam stand, large piece of bedding

foam or a thick bath towel will work well and help

protect the model from damage during assembly.

The Spektrum trademark is used with permission

of Bachmann Industries, Inc.

Содержание Alpha Sport 450 PNP

























Результаты поиска

Содержание Alpha Sport 450 PNP

Отзывы:

Похожие инструкции для Alpha Sport 450 PNP

Бренды по названию

Популярные бренды

E-FLITE Alpha Sport 450 PNP, Инструкция по сборке

Результаты поиска

Содержание Alpha Sport 450 PNP

Отзывы:

Похожие инструкции для Alpha Sport 450 PNP

Бренды по названию

Популярные бренды