background image

19

E-flite Alpha Sport 450 PNP Assembly Manual

Range Test your Radio

Before each flying session, and especially with a new 

model, it is important to perform a range check. It 

is helpful to have another person available to assist 

during the range check. If you are using a Spektrum 

transmitter, please refer to your transmitter’s manual for 

detailed instructions on the range check process.

  1. With the model resting on the ground, stand 30 

paces (approximately 90 feet) away from the model.

  2. Face the model with the transmitter in your 

normal flying position. Be sure the throttle is in the 

full down position and plug the flight battery into 

the speed control.

  3. As you move the controls, watch to be sure the 

airplane’s motor and controls operate smoothly. 

You should have total control of the model at 30 

paces (90 feet).

30 paces (90 feet/28 meters)

  4. If control issues exist, call the Horizon Support 

Team at 1 877 504 0233 or go to 

horizonhobby.

com

 to find a local Spektrum distributor in your 

country for service if you are using a Spektrum 

radio system.

flying your Alpha Sport 450 PNP

The Alpha Sport 450 is a park flyer version of the 

famous Hangar 9 Alpha trainer but with reduced 

dihedral for a more spirited flight envelope. Takeoffs 

are easily accomplished with the addition of full power 

and a slight amount of up elevator. Takeoff rolls are 

routinely in the 20–30 foot range with a strong climb 

out. Once at altitude, trim the plane for level flight 

at 3/4 throttle. You will find the model behaves in a 

very benign way in all aspects of the flight envelope. 

Inverted flight requires a fair amount of down elevator, 

and the roll authority is quite good with the prescribed 

high rate. This model is not capable of extreme 

performance flight and was never designed for that. 

Gentle majestic flight is its main purpose.

Landings are easily accomplished by reducing power 

and gliding down to your favorite landing spot on the 

runway with a very short roll out. We hope you enjoy 

flying the Alpha as much as we do.

Happy landings. 

Age Requirement

Age Recommendation: 14 years or over. This is not 

a toy. This product is not intended for use by children 

without direct adult supervision.

Safety do’s and don’ts for Pilots

•   Check all control surfaces prior to each takeoff.

•   Do not fly your model near spectators, parking 

areas or any other area that could result in injury to 

people or damage of property.

•   Do not fly during adverse weather conditions. Poor 

visibility can cause disorientation and loss of control 

of your aircraft. Strong winds can cause similar 

problems.

•   Do not take chances. If at any time during flight you 

observe any erratic or abnormal operation, land 

immediately and do not resume flight until the cause 

of the problem has been ascertained and corrected. 

Safety can never be taken lightly.

•  Do not fly near power lines.

Содержание Alpha Sport 450 PNP

























Отзывы: