background image

18

E-flite Alpha Sport 450 PNP Assembly Manual

Center of Gravity

An important part of preparing the aircraft for flight is 

properly balancing the model.

Caution: do not inadvertently skip this step!

The recommended Center of Gravity (CG) location for 

the Alpha 450 is 3

1

/

4

 to 3

1

/

(82 to 88mm) back from 

the leading edge of the top wing. Mark the location for 

the Center of Gravity on the bottom of the top wing in 

the center as shown.

When balancing your Alpha 450 Sport 450, support 

the plane upright at the marks made on the bottom of 

the wing with your fingers or a commercially available 

balancing stand. Move the motor battery as necessary 

so the model hangs level or slightly nose down. This is 

the correct balance point for your model.

BALANCEd MOdEL

NOSE hEAvy - MOvE BATTERy BACK

If the model is positioned with the nose facing 

downward as shown in the illustration, it will be 

necessary to move the battery rearward in the battery 

compartment to achieve the correct Center of Gravity.

TAIL hEAvy - MOvE BATTERy fORWARd

If the model is positioned with the tail facing 

downward as shown in the illustration, it will be 

necessary to move the battery forward in the battery 

compartment to achieve the correct Center of Gravity.

Once you model is balanced correctly, it is 

recommended to mark the position of the battery in the 

battery compartment using a pencil or felt-tipped pen. 

This way it can be returned to the same location after it 

has been removed for charging.

After the first flights, the CG position can be adjusted 

for your personal preference.

Содержание Alpha Sport 450 PNP

























Отзывы: