Aeronaut Grumman F7 F-3 Tigercat Building Instructions Download

Page: 1 / 9

Grumman F7 F-3 Tigercat

Building instructions - Grumman F7 F-3 Tigercat

Building
instructions

Grumman F7 F-3

Tigercat

Electric RC model

Order No. 1349/00

Specification:

Wingspan

approx.

1330 mm

Length

approx.

1063 mm

Wing area

approx.

27.5 dm²

Tailplane area

approx.

6.6 dm²

Total surface area

approx.

34.1 dm²

All-up weight with 10 cells

approx.

1950 g

Total surface area loading
at 1950 g take-off weight

approx.

57.2 g/dm²

Wing loading (wing only)

approx.

70.9 g/dm²

RC functions

: ailerons, elevator, rudder, motor speed

Replacement parts

GRP fuselage

Order No. 1349/02

GRP nacelles

Order No. 1349/03

Pair wing panels

Order No. 1349/05

Tailplane

Order No. 1349/09

Canopy

Order No. 1349/04

“aero-naut” Modellbau
Stuttgarterstr. 18-22

D-72766 Reutlingen
Germany

Summary of Contents for Grumman F7 F-3 Tigercat










Search results

Summary of Contents for Grumman F7 F-3 Tigercat

Reviews:

Related manuals for Grumman F7 F-3 Tigercat

Brands by name

Popular brands

Aeronaut Grumman F7 F-3 Tigercat, Building Instructions

Search results

Summary of Contents for Grumman F7 F-3 Tigercat

Reviews:

Related manuals for Grumman F7 F-3 Tigercat

Brands by name

Popular brands