E.F. Johnson Company CONVENTIONAL VOTING RECEIVER Скачать руководство пользователя страница 25

Страница: 25 / 148

VHF RECEIVER

2-9

July 2000

Part No. 001-2000-720

4. Highlight DEFAULT, press Enter.

5. Highlight EDIT, press Enter.

6. Highlight SETUP PARAMETERS, press Enter.

7. Change the Repeater number and other parameters

as required for this repeater, press F2.

8. Highlight EDIT, press Enter.

9. Highlight FILES, press Enter.

10.Highlight SAVE, press Enter.

11. Repeater 2 is added to the Repeater List in file

site1.dat.

Table 2-1 CVR SETUP PARAMETERS

Parameter

Response

Description

Repeater Number

1-30

Each receiver is assigned a number from 1-30 for reference.

Receive Frequency

VHF
UHF
800 MHz

Each receiver is programmed with a frequency or channel number that it is
operating on.

VHF Frequency Step

5000 Hz
6250 Hz

This is the allowable frequency spacing to eliminate the chance of incorrect
synthesizer settings arising from ambiguous frequencies.

Содержание CONVENTIONAL VOTING RECEIVER





















































































































































Результаты поиска

Содержание CONVENTIONAL VOTING RECEIVER

Отзывы:

Похожие инструкции для CONVENTIONAL VOTING RECEIVER

Бренды по названию

Популярные бренды

E.F. Johnson Company CONVENTIONAL VOTING RECEIVER, Руководство пользователя

Результаты поиска

Содержание CONVENTIONAL VOTING RECEIVER

Отзывы:

Похожие инструкции для CONVENTIONAL VOTING RECEIVER

Бренды по названию

Популярные бренды