E.F. Johnson Company CONVENTIONAL VOTING RECEIVER Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 148

background image

800 MHz RECEIVER

4-6

July 2000
Part No. 001-2000-720

Full CVR

This menu selection walks through the align-

ment of the entire repeater. The Receiver and Exciter
portions are performance tests and adjustments. The
Audio and Data portions are level adjustments for the
CVR Interface Board. Refer to Figure 4-29 for an
alignment points diagram for the Interface Board.

CVR To Voter Interface

Figure 4-22 CVR TO VOTER INTERFACE

This menu selection walks through the align-

ment of the audio output level setting of the receiver.

4.2.7 UTILITIES

Figure 4-23 UTILITIES MENU

COM Port

This is the COM port used to send and receive

data from the Repeater MPC. An interface cable con-
nects the Repeater to the computer (see Figure 4-25

).

Figure 4-24 COM PORT SELECTION

Figure 4-21 TEST PROGRAMMING FLOWCHART

All Test

Receiver Test

TCXO Frequency Adjust

Audio Distortion

Hum & Noise Measurement

SINAD Measurement

Squelch Adjust

Data Level Adjust

Miscellaneous Tests

Receiver

TEST

All Receive Tests

All Operational Tests

Handshake Test

Alarm Test

Full Rptr/Station/CVR

Voter Interface

CVR Setup

RSSI Adjustment (Factory)

RSSI Adjustment (Field)

CVR Operation

CVR Audio Level Adjustment

CVR FSK Level Adjustment

Revert Audio Adjustment (Local Site Only)

«
...
72
73
74
75
76
...
»

Содержание CONVENTIONAL VOTING RECEIVER





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для CONVENTIONAL VOTING RECEIVER

CQVD7700U - CAR A/V DVD NAV

Бренд: Panasonic Страницы: 133

Бренд: Sansui Страницы: 59

Бренд: Blaupunkt Страницы: 17

Бренд: Harman Kardon Страницы: 64

Бренд: Elvaco Страницы: 2

Бренд: Aiwa Страницы: 23

Бренд: Renkforce Страницы: 8

Бренд: iSimple Страницы: 12

Бренд: adstec Страницы: 21

Бренд: Sangean Страницы: 48

Бренд: IMG STAGELINE Страницы: 24

Бренд: AKK Technology Страницы: 5

Бренд: Icom Страницы: 53

Audio 30 ECE Typ 3300

Бренд: Becker Страницы: 49

Бренд: Zamel Страницы: 2

Бренд: Pyle Страницы: 11

Бренд: Vigitron Страницы: 2

Бренд: Johnson Controls Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды