E.F. Johnson Company CONVENTIONAL VOTING RECEIVER Скачать руководство пользователя страница 45

Страница: 45 / 148

UHF RECEIVER

3-3

July 2000

Part No. 001-2000-720

3.2.3 EDIT

Figure 3-6 EDIT MENU

This menu is used to create new files and set or

change the CVR operating parameters. The filename
for the CVRs in this file is shown in the lower left cor-
ner of the screen.

Figure 3-7 SETUP PARAMETERS

Setup Parameters

This programs the Receiver parameters and

options of each CVR at a Site. The following para-
graphs explain the parameters that are set by this
screen (see Figure 3-7) and give a brief description of
each.

NOTE: The parameters are shown in the lower left of
the pop-up screen for reference.

Repeater Number

Each CVR is programmed with a repeater num-

ber from 1-30 for reference. Number selection can be
arbitrary as long as each CVR is assigned a different
number.

Receiver Frequency

Each CVR is programmed with the frequency

that it is operating on.

Select Repeater

Select the repeater number to be programmed or

edited from the pop-up menu (see Figure 3-8). Move
the cursor with the arrow keys to highlight the repeater
number and press Enter.

Figure 3-8 REPEATER LIST

Repeater Type Selection

This screen (see Figure 3-9) selects the repeater

type and features:

Channel Bandwidth

25 kHz
12.5 kHz

Frequency Range

370-480 MHz
480-512 MHz

Figure 3-9 REPEATER TYPE SELECTION

Delete Repeater

Figure 3-10 DELETE REPEATER

Repeater List

default

Rptr 1

-------

Rptr 30

Select Rptr To Delete
Rptr 1

Содержание CONVENTIONAL VOTING RECEIVER





















































































































































Результаты поиска

Содержание CONVENTIONAL VOTING RECEIVER

Отзывы:

Похожие инструкции для CONVENTIONAL VOTING RECEIVER

Бренды по названию

Популярные бренды

E.F. Johnson Company CONVENTIONAL VOTING RECEIVER, Руководство пользователя

Результаты поиска

Содержание CONVENTIONAL VOTING RECEIVER

Отзывы:

Похожие инструкции для CONVENTIONAL VOTING RECEIVER

Бренды по названию

Популярные бренды