E.F. Johnson Company CONVENTIONAL VOTING RECEIVER Скачать руководство пользователя страница 28

Страница: 28 / 148

VHF RECEIVER

2-12

July 2000
Part No. 001-2000-720

7. Set the generator to 100

V into the receiver with a

1 kHz tone at

3 kHz deviation.

(1000

V at the generator with 20 dB pad gives

100

V at the receive antenna.)

8. Tune Z205 for 2V

0.05V at U201, pin 9.

9. Tune RV203 for 387 mV RMS,

5 mV RMS, at

TP202.

10.Adjust RV202 for 2V ±0.05V at TP202.

11. Connect a distortion analyzer to TP202.

12.Tune L201, L203, L204 and L206 for minimum

distortion <5%, (typically <3%).

13.Repeat Step 12 then Steps 8, 9 and 10.

2.3.7 AUDIO DISTORTION

1. On the Interface Board, plug a 16 ohm load at J104.

2. Connect a distortion analyzer to the 16 ohm load.

3. On the Interface Board, measure the distortion of

the receive audio at J104 with the local volume con-
trol set to 2.8V RMS.

4. The reading shall be less than 3%.

(Typically less than 1%.)

5. On the Interface Board, measure receive sensitivity

at J104.

6. The reading should be less than 0.35

(Typically 0.25

V.)

7. The software programs the synthesizer for

1 MHz above the Receive frequency.

8. Receive sensitivity should be less than 0.35

(Typically less than 0.30

V.)

9. The software programs the synthesizer for

1 MHz below the Receive frequency.

10.Receive sensitivity should be less than 0.35

(Typically less than 0.30

V.)

11. Adjust the signal generator level to produce 15 dB

SINAD.

12.Adjust RV201 for 0.5V ±0.02V at TP201.

2.4 FULL CVR TEST

1. Select TEST - FULL RPTR/STATION/CVR and

press Enter.

NOTE: All audio generators and audio voltmeters are
unbalanced unless specifically stated otherwise.

2.4.1 VOLTAGE MEASUREMENTS

1. Disconnect the receiver-to-interface cable

(20-pin) from J201 of the Interface board.

2. Apply power to the Interface board.

3. Measure the voltages at the following pins.

U221, pin 1

+12V DC

0.4V

U223, pin 2

+9V DC

0.4V

U224, pin 2

+5V DC

0.2V

U204, pin 7

+1.25V DC

0.06V

Junction of L202/C279 -5V DC

0.4V

4. Apply power to the Receiver by plugging the 20-pin

cable from the Interface Board into J201 (see
Figure 2-29

2.4.2 RECEIVER FREQUENCY CHECK

1. Check the receiver injection frequency with a

"sniffer" pickup loop, or RF probe and a suitable
frequency counter placed near TP102.

2. TCXO Adjustment

Set Y401 (TCXO) for the Injection Frequency
±50 Hz (Inj Freq = chnl freq + 52.95 MHz).

Receiver Audio Distortion Measurement

1. Adjust the RF generator for 100

V into the receiver

with a 1 kHz tone at

3 kHz deviation.

2. Adjust R207 for 0 dBm (775 mV RMS) at J210.

Содержание CONVENTIONAL VOTING RECEIVER





















































































































































Результаты поиска

Содержание CONVENTIONAL VOTING RECEIVER

Отзывы:

Похожие инструкции для CONVENTIONAL VOTING RECEIVER

Бренды по названию

Популярные бренды

E.F. Johnson Company CONVENTIONAL VOTING RECEIVER, Руководство пользователя

Результаты поиска

Содержание CONVENTIONAL VOTING RECEIVER

Отзывы:

Похожие инструкции для CONVENTIONAL VOTING RECEIVER

Бренды по названию

Популярные бренды