E.F. Johnson Company CONVENTIONAL VOTING RECEIVER Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 148

background image

2-1

July 2000

Part No. 001-2000-720

VHF RECEIVER

SECTION 2 VHF RECEIVER

2.1 RECEIVER PROGRAMMING

2.1.1 2004PGMR PROGRAMMER

When the program is loaded into the computer

and executed, the menu shows the files available from
the directory. The program is used to Create, Edit,
Transfer and Receive the repeater and channel parame-
ters described in Section 2.2.

I M P O R T A N T

The commands and displays referred to in this Section
are for the IBM PC and may differ from IBM compati-
ble. Refer to the computer’s operating system manual
for command explanations.

2.1.2 ALIGNMENT SOFTWARE

The software for the CVR programs the Interface

Board to open and close the audio/data gates necessary
for the alignment selected from the Test-Full Rptr/Sta-
tion/CVR menu. Under the menu heading Test are the
alignment procedures for the Receiver, overall Full
CVR (see Section 2.4) including the Interface Board
(see Figure 2-1).

Refer to Section 2.3 for Alignment Procedures as

shown in the program, alignment points diagrams and
test setup diagrams.

Figure 2-1 CVR TEST MENU

2.1.3 HELP F1

Help screens are available for most parameters

and options in this program. Whenever a parameter or
options clarification is needed, press F1 and if a help
screen is available it will pop-up on the screen. Press
Escape <ESC> to exit the pop-up screen.

2.2 PULL DOWN MENUS

2.2.1 MENU DISPLAYS

The menus available are listed at the top of the

screen. Move the cursor with the arrow keys to high-
light the menu name. Press Enter to view the menu
and the arrow keys to scroll through the menu. Call up
the highlighted selection by pressing Enter.

2.2.2 FILE MENU

This menu manipulates new or existing files into

directories and saves files to be called up at another
time.

Figure 2-2 FILE MENU

Load

Load reads information from a stored file. The

program requests the filename to be loaded into the
buffer. The filename from a disk can be entered in the
highlighted area. Then move the cursor down with the
arrow key and highlight “Ok” and press Enter. To
select an existing file, use the arrow keys to move
down the menu list and press Enter when the high-
lighted filename is the file to load.

«
...
15
16
17
18
19
...
»

Содержание CONVENTIONAL VOTING RECEIVER





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для CONVENTIONAL VOTING RECEIVER

C-Tech HD 6600 SST

Бренд: Clarke-tech Страницы: 32

Бренд: Retekess Страницы: 2

Omni Pager OP1097-2

Бренд: Silent Call Communications Страницы: 2

Бренд: Avenview Страницы: 15

6.1 Channel AV Reciever LR-6500

Бренд: Luxman Страницы: 36

Бренд: Peiying Страницы: 12

TELEVISION RECEIVER

Бренд: Zenith Страницы: 8

Бренд: Woxcon Страницы: 7

Бренд: LVSUN Страницы: 7

Car Show GM1210

Бренд: ADC Страницы: 16

Бренд: Cypress Страницы: 16

Бренд: Audiovox Страницы: 78

Бренд: Strong Страницы: 25

Бренд: Radio Shack Страницы: 44

Бренд: Vertex Страницы: 66

Бренд: BUXTON Страницы: 40

Бренд: Yaesu Страницы: 32

ATTEROTECH unBT2A

Бренд: QSC Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды