E.F. Johnson Company CONVENTIONAL VOTING RECEIVER Скачать руководство пользователя страница 101

Страница: 101 / 148

900 MHz RECEIVER

5-11

July 2000

Part No. 001-2000-720

Receiver Hum and Noise Measurement

1. Adjust the RF generator for 100

V into the

receiver with a 1 kHz tone at

3 kHz.

2. On the Interface Board, connect a 16 ohm load and

distortion analyzer to J204.

3. Adjust R262 for 2.8V RMS.

4. Remove modulation from the RF generator.

The measured level must be

≤

-45 dB.

Receiver SINAD Measurement

1. Adjust the RF generator for 100

V into the

receiver with a 1 kHz tone at

3 kHz.

2. On the Interface Board, connect a 16 ohm load and

distortion analyzer to J204.

3. Adjust R262 for 2.8V RMS.

4. 12 dB SINAD reading should be

≤

0.35

Receiver Squelch Adjustment

1. Adjust the RF generator for 100

V into the

receiver with a 1 kHz tone at

3 kHz.

2. On the Interface Board, connect a 16 ohm load

and distortion analyzer to J204.

3. Adjust R262 for 2.8V RMS.

4. Set the RF generator output for 5 dB SINAD.

5. On the Interface Board, adjust R222 so the Receiver

just squelches.

6. Increase the RF generator output until the Receiver

unsquelches. Reading should be

≤

10 dB SINAD.

Receiver Data Level Adjustment

1. Adjust the RF generator for 100

V into the

receiver with a 100 Hz tone at

1 kHz.

2. Insert voltmeter probes into J202 on the Interface

Board and connect to an AC voltmeter.

3. Adjust R248 to achieve 340 mV RMS (-7.1 dBm).

Receiver RSSI Adjustment

NOTE: Use this procedure only when an audio analyz-
er is unavailable.

1. Adjust the RF generator for 0.29

V into the

Receiver with a 1 kHz tone at

3 kHz.

2. Adjust R261 in the Receiver for 0.8V DC (

0.02V

DC) at TP3.

Receiver Miscellaneous Tests (Optional)

Several additional tests may be performed on the

Receiver as listed below:

•

Signal Displacement Bandwidth

•

Adjacent Channel Rejection

•

Offset Channel Selectivity

•

Intermodulation Rejection

•

Spurious Rejection

•

Audio Response

•

Audio Sensitivity

Perform the Test desired using the appropriate RF

Generators, modulation frequencies, levels, RS-232
levels and test probes following the latest TIA docu-
ment measurement procedures.

Handshake Test

1. Program a portable or mobile for the

following parameters.

Home Repeater - Same as repeater number.
System Key - Same as repeater
Status Channel - Same as repeater channel.
Home Channel - Same as repeater channel.
Encode ID = 1
Decode ID = 1
UID = 1
Site = 1

2. The repeater is now in Normal Operation mode.

3. Key the radio several times on the programmed

System/Group. Display shall indicate "4" every
time. (Proper Tx/Rx antenna connections are
assumed.)

Содержание CONVENTIONAL VOTING RECEIVER





















































































































































Результаты поиска

Содержание CONVENTIONAL VOTING RECEIVER

Отзывы:

Похожие инструкции для CONVENTIONAL VOTING RECEIVER

Бренды по названию

Популярные бренды

E.F. Johnson Company CONVENTIONAL VOTING RECEIVER, Руководство пользователя

Результаты поиска

Содержание CONVENTIONAL VOTING RECEIVER

Отзывы:

Похожие инструкции для CONVENTIONAL VOTING RECEIVER

Бренды по названию

Популярные бренды