E.F. Johnson Company CONVENTIONAL VOTING RECEIVER Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 148

background image

UHF RECEIVER

3-9

July 2000

Part No. 001-2000-720

2. Tune the VCO capacitor C803 for +7V DC

±

0.05V

at TP401.
Increase the receive frequency by 1 MHz. The volt-
age on TP401 shall be less than 10.5V.
Decrease the receive frequency by 1 MHz. The
voltage on TP401 shall be greater than 3.5V.

3. Alternately tune L140 and L141 in 1/2-turn to

1-turn increments until a voltage is measured at
TP101. At that time, tune L140 for a peak, then
L141 for a peak.

4. Retune L140/L141 for a peak at TP101.

For Receivers operating within 3 MHz of the top of the
receive band (467-470 MHz).

1. Program the Synthesizer for the Highest receive fre-

quency.

2. Set the control line voltage for 12V at TP401.

Check 3 MHz below the programmed frequency
(i.e. 467 MHz) to verify that the control voltage at
TP401 is greater than 2V. The repeater receiver can
now be programmed for the desired operating fre-
quency.

For Receivers operating within 3 MHz of the bottom of
the receive band (430-433 MHz).

1. Program the Synthesizer for the Lowest receive fre-

quency.

2. Set the control line voltage for 2V at TP401.

Check 3 MHz above the programmed frequency
(i.e. 433 MHz) to verify that the control voltage at
TP401 is less than 12V. The repeater receiver can
now be programmed for the desired operating
frequency.

NOTE: The Channel Frequency and Synthesizer
Frequency appear at the bottom of the screen.

3.3.4 RECEIVER FREQUENCY ADJUST

1. Place a pick-up loop (sniffer) or RF probe connected

to a frequency counter near L139.

2. Set Y401 (TCXO) for the Injection Frequency

±

50 Hz (Inj Freq = chnl freq + 52.95 MHz).

3.3.5 VCO TEST

1. The software programs the synthesizer for

1 MHz above the receive channel.

2. The voltage on TP401 should be < 10V.

3. Record the voltage on TP101 __________.

4. The software programs the synthesizer for

1 MHz below the receive channel.

5. The voltage on TP401 should be > 2V.

6. Record the voltage on TP101 __________.

7. If the voltages recorded in Steps 3 and 6 are not

within

±

0.2V, tune L141 as required to balance the

voltage readings.

8. The software programs the synthesizer for the

receive frequency.

3.3.6 FRONT END ADJUSTMENTS

NOTE: Verify that the appropriate IF jumpers (J203,
J204, J205) are selected.

1. Set the signal generator to the receive frequency at a

level sufficient to produce an output voltage at
TP201 or J201, pin 7 (RSSI Output).

2. Tune L102, L103, L104, L108, L109 and L110, then

repeat, for a peak voltage at TP201. Decrease the
generator output level to maintain a
2-3V reading at TP201.

FOR 12.5 kHz CHANNELS:

NOTE: Perform this test if C239 and C249 are placed
on the board.

1. Set the generator to an RF level sufficient to produce

2V DC at TP201.

2. Remove any modulation from the signal generator.

3. Increase the signal generator RF frequency 2.5 kHz.

4. Adjust C239 for peak DC voltage at TP201.

«
...
49
50
51
52
53
...
»

Содержание CONVENTIONAL VOTING RECEIVER





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для CONVENTIONAL VOTING RECEIVER

Бренд: Jensen Страницы: 96

Бренд: Salora Страницы: 7

Бренд: Intermatic Страницы: 56

Бренд: Hallicrafters Страницы: 9

Бренд: Alpine Страницы: 36

Бренд: Aiwa Страницы: 13

Бренд: VDO Страницы: 14

Бренд: Teac Страницы: 40

Бренд: GPX Страницы: 12

Бренд: Yongnuo Страницы: 15

Бренд: Acesori Страницы: 2

Бренд: Jensen Страницы: 22

Бренд: D+M Group Страницы: 19

Бренд: AMX Страницы: 1

Бренд: Jensen Страницы: 22

Бренд: AOR Страницы: 24

Бренд: Topfield Страницы: 62

Бренд: Telefunken Страницы: 63

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды