Dynapac DRP45DX страница 50 Скачать руководство пользователя

Страница: 50 / 124

5.1 Notes on safety

If the following tests reveal damages or other defects, the machine

must not be operated, until these deficiencies have been corrected.

Do not operate the machine with defective indicators and control

elements.

Safety installations must not be removed or made ineffective.

Do not change any fixed settings.

WARNING!
Health hazard caused by fuels and lubricants!

–

Safety regulations and environmental protec-

tion regulations must be followed when han-

dling fuels and lubricants

Chapter 3.4 ‘Han-

dling fuels and lubricants’ on page 23

WARNING!
Danger of injury caused by rotating parts!

–

Before starting work on the machine make sure

that the engine can not be started.

Park the machine safely

Chapter 6.4 ‘Parking the machine

in secured condition’ on page 63

Open and secure the protection hood

Chapter 8.2.1.1

‘Opening the protection hood’ on page 71

Close the protection hood again after work is completed

Chapter 8.2.1.2 ‘Closing the protection hood’ on page 72

Checks prior to start up – Notes on safety

DRP45DX

Содержание DRP45DX





























































































































Результаты поиска

Содержание DRP45DX

Отзывы:

Похожие инструкции для DRP45DX

Бренды по названию

Популярные бренды

Dynapac DRP45DX, Руководство по эксплуатации

Результаты поиска

Содержание DRP45DX

Отзывы:

Похожие инструкции для DRP45DX

Бренды по названию

Популярные бренды