manualshive.com logo in svg

Dynapac DRP45DX, Руководство по эксплуатации

Поделиться
Скачать
Dynapac DRP45DX Скачать руководство пользователя страница 118

9.7  Malfunctions during operation

Fault

Possible cause

Remedy

The machines

vibrates forward

with a strongly

reduced speed

Air in the steering rod hydraulic system

Release pressure from the steering rod

The oil level in the exciter shaft housing

is too high

Check the oil level in the exciter shaft

housing

Protective equipment:

n

Working clothes

n

Safety shoes

n

Protective gloves

1.

Park the machine safely

 

Ä

 Chapter 6.4 ‘Parking the machine

in secured condition’ on page 63

.

2.

Press the handle forward against the end stop and hold it in

this position.

3.

Carefully loosen the filler screw (1).

ð

The air makes a slight hissing sound when escaping.

4.

Wait until all air has escaped and then tighten the filler screw,

tightening torque: 45 Nm (33.2 ft

·

lbf).

Release pressure from the steering

rod

B-692-0092

1

Fig.  143

Troubleshooting – Malfunctions during operation

 

DRP45DX

 

118

Содержание DRP45DX





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды