Dynamax Dynamet 5 Скачать руководство пользователя

Страница: 83 / 83

MaxiMet

Applications

WIND SPEED

Range

0.1 m/s to 60 m/s

Accuracy

± 3% to 40 m/s,

± 5% to 60 m/s

Resolution m/s

0.01

Starting Speed

0.1 m/s

Sampling Rate

1 Hz

Units

m/s, km/hr, mph, kts, ft/min

WIND DIRECTION

Range

0-359°

Accuracy

± 3° to 40 m/s

± 5° to 60 m/s

Resolution

1°

Sampling Rate

1 Hz

Units

Degrees

TEMPERATURE

Range

-40°C to +70°C

Resolution

0.1

Accuracy

± 0.3°C @ 20°C

Sampling Rate

1 Hz

Units

°C, °F, °K

HUMIDITY

Range

0-100%

Resolution

Accuracy

± 2% @ 20 C (10%-90% RH)

Sampling Rate

1 Hz

Units

% Rh, g/m3, g/Kg

DEW POINT

Range

-40°C to +70°C

Resolution

0.1

Accuracy

± 0.3°C @ 20°C

Units

°C, °F, °K

Sampling Rate

1 Hz

ENVIRONMENTAL CONDITIONS

IP Rating

Operational

Temperature Range:

-40°C to +70°C

EMC Standard:

BS EN 61326 : 2013
FCC CFR47 parts 15.109

CE Marking

YES

RoHS compliant

YES

Weight

0. Kg

Origin

PRESSURE

Range

300 to 1100

Resolution

0.1 hPa

Accuracy

± 0.5 hPa @ 25°C

Sampling Rate

1 Hz

Units

hPa, bar, mmHg, inHg

POWER

Power Supply

5 to 30 Vdc

Power (Nominal)

12 Vdc

25 mA continuous high

mode. 0. mA eco-power

mode (1 hour polled)

OUTPUTS

Output rate

1/s, 1/min, 1/hr

Digital Comms

Modes

Serial RS232, RS422,

RS485, SDI-12, NMEA,

MODBUS, ASCII

Analogue Outputs Available via separate

optional device

10808 Fallstone Road

Suite 350

Houston, TX 77099

Tel: (281) 564-5100

www.dynamax.com

[email protected]

Содержание Dynamet 5




















































































Результаты поиска

Содержание Dynamet 5

Отзывы:

Похожие инструкции для Dynamet 5

Бренды по названию

Популярные бренды

Dynamax Dynamet 5, Руководство пользователя

Результаты поиска

Содержание Dynamet 5

Отзывы:

Похожие инструкции для Dynamet 5

Бренды по названию

Популярные бренды