Dynamax Dynamet 5 Скачать руководство пользователя | Manualshive

Страница: 58 / 83

background image

Dynamet 5

57

7.0 COMMUNICATIONS

Dynamet 5 weather station and PC400 has added communications and networking features for
remote  long  distance  and  cable  communications  and  scheduling.  Below  is  a  list  of
communication  devices  offered  by  Dynamax  and  are  tested  on  Dynamet  5  for  signal  strength
and  transmission  range.  For  advanced  remote  network  communications  choose  LoggerNet
software.

This  is  a  basic  serial  communication  interface  using  9  conductor  serial  cable,  is  shown  in  the
figure  below.  6’  serial  cable  is  supplied  with  Flow32  and  can  be  extended  up  to  200’  without
loosing any signal. If a longer cable is required contact Dynamax. For distances longer than 200’
it is recommended to use either a short-haul modem or RF interface.

Radio modem for wireless  communications up to 40Miles (64KM) at  baud rate 9600bps. Baud
speed  is  programmable.  LoggerNet  software  is  equipped  with  capability  to  program,  and
configure  RFMX  modems  in  point-to-point  and  point-to-multi-point  modes.  Refer  to  RFMX
modem  manual  for  setup  and  programming  details.  A  simple  communication  setup  between
Dynamet  5  weather  station  and  PC  using  RF  modems  is  shown  below  along  with  modem
addresses.

Serial data cable:

RF Radio Modem (RFMX):

Logger

Logger

«
...
56
57
58
59
60
...
»

Содержание Dynamet 5




















































































Отзывы:

Нет отзывов

Похожие инструкции для Dynamet 5

Бренд: Tripp Lite Страницы: 42

Бренд: WEATHER DIRECT Страницы: 24

MH-3621-U3 Clone

Бренд: archgon Страницы: 14

Бренд: WEATHER DIRECT Страницы: 24

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

4-182-698-82(2)

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 19

Бренд: Sony Страницы: 32

ATS-SW10Ti Marketing

Бренд: Sony Страницы: 48

Бренд: Sony Страницы: 100

Бренд: Dok Страницы: 21

Бренд: La Crosse Technology Страницы: 10

Бренд: La Crosse Страницы: 10

iPod Docking System

Бренд: Cambridge Audio Страницы: 2

Бренд: IBM Страницы: 67

Бренд: National Geographic Страницы: 50

Бренд: Oregon Scientific Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды