Dynamax Dynamet 5 Скачать руководство пользователя | Manualshive

Страница: 24 / 83

background image

Dynamet 5

23

3.2.3

Install Dynamet 5 Enclosure

Dynamet  5  weather  station  enclosure  contains  CR1000  data  logger,  and  other  storage  of
communication  peripherals  if  any.  Sensor  cables,  Power  cables,  Communication  cables
connected to the data logger or any peripherals routed out of the enclosure through a PVC
conduit.  So  it  is not  necessary  of an end-user  to  make  any  wiring  inside  the  enclosure.  All
the connectors are accessible out of the box. Position the enclosure on the north side of the
mast or tower (northern hemisphere). Secure enclosure as shown in the figure using U-bolts
and mounting brackets. Route the 12AWG wire from the Ground Lug on the enclosure to the
tripod-grounding clamp. Tighten the screws. Grounding is critical not only for the accuracy of
data/ reduce signal noise but also to protect equipment from any lightening surges.

«
...
22
23
24
25
26
...
»

Содержание Dynamet 5




















































































Отзывы:

Нет отзывов

Похожие инструкции для Dynamet 5

Бренд: IOGear Страницы: 20

Weather Forecaster 00821

Бренд: ACU-RITE Страницы: 5

Бренд: La Crosse Technology Страницы: 12

Бренд: Columbia Weather Systems Страницы: 49

Weather Display

Бренд: Columbia Weather Systems Страницы: 60

Бренд: Conrad Страницы: 4

Бренд: Conrad Страницы: 52

Бренд: iHome Страницы: 13

Бренд: cable matters Страницы: 12

Бренд: Sainlogic Страницы: 60

DisplayLink IB-DK2288AC

Бренд: Icy Box Страницы: 41

Бренд: La Crosse Technology Страницы: 24

Бренд: La Crosse Technology Страницы: 13

Бренд: Campbell Страницы: 81

Бренд: Levenhuk Страницы: 26

Бренд: La Crosse Technology Страницы: 10

Бренд: La Crosse Страницы: 2

Бренд: Fine Offset Electronics Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды