manualshive.com logo in svg

Duratrax Street force GP2, Руководство по сборке и эксплуатации

Поделиться
Скачать
Duratrax Street force GP2 Скачать руководство пользователя страница 16

16

Steering

1. Install a 4.3mm ball stud (124) into the top of the inner hole of

the lower right servo saver arm (108) and the left servo saver
arm (107). Then install a 4.3mm ball stud (124) into the bottom
of the outer hole of the lower right servo saver arm (108) and
the left servo saver arm (107).

2. Install a servo saver bushing in the top and bottom of the left

servo saver arm (107). Note: make sure the bushings are
properly seated to prevent binding.

3. Install the left servo saver arm assembly onto the left servo

saver post (110). Secure the servo saver assembly onto the
servo saver post with a 2.5mm e-clip (U).

4. Install the servo saver tube (105) into the right upper servo

saver arm (106). Note: The tube keys into the servo saver
arm. Make sure the tube is properly seated in the upper arm
to prevent binding.

5. Install the lower right servo saver arm (108) onto the tube (105)

and slide it next to the upper right servo saver arm (106). Make
sure the two arms properly key together.

6. Install the servo saver spring (111) and the servo saver

adjustment nut (112) onto the servo saver tube (105).

7. Install the right servo saver arm assembly onto the right servo

saver post (113).

8. Attach the right and left servo saver assemblies together using

the steering drag link.

1. Install the brake cam (73) into the right rear bulkhead (5).
2. Install the brake caliper spacer (114) into the right rear

bulkhead (5). Note: Make sure the brake caliper spacer
keys into the flat spot on the brake cam.

3. Install a 2x10mm pin (40) into the 2 speed main shaft (72).
4. Install the brake nut (69) onto the 2 speed main shaft (72).

Note: The brake nut keys onto the 2x10mm pin.

6. Install another 2x10mm pin (40) in the main

shaft (72).

7. Install a small pulley (49) onto the main shaft

(72) and key it onto the 2x10mm pin (40).

5. Install a brake caliper (70) and then slide the brake disc

(71) onto the brake nut (69). Then install the other brake
caliper (70) onto the right rear bulkhead (5). Secure them
to the bulkhead using two 3x12mm screws (D).

Note: When tightening the brake caliper
screws, make sure you do not over tighten
them. This could cause the brakes to engage
prematurely. Also, setting them too loose
can cause the brakes to be weak or not work.

8. Install a belt guide (50) onto the small pulley (49). Note: Make sure

the guide keys onto the pulley. Secure the assembly onto the main
shaft by installing a 4mm e-clip (V).

Brake

Содержание Street force GP2





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды