18
motor cables, taking care not to damage the support of the brush holder blades.
drawing 3.3.
4) ENGINE ASSEMBLY
(See the drawings in section 4).
The surface on which the engine will be fixed to the ground must be perfectly smooth
and flat. It is advisable to arrange a higher floor from the ground to avoid possible
water infiltration in case of cold. It is also advisable to add the optional plate Ref.
PLAK7800, which allows a better adjustment of the final position of the motor with re-
spect to the rack. This optional accessory facilitates the correction of the position that
may be necessary over time or in relation to the change of season due to the expan-
sion of the materials in relation to the temperature.
The height of the surface where the motor is to be fixed must also be studied in rela-
tion to the position of the frame that will be installed on the gate.
After having determined the ideal mounting position of the motor and its height with
respect to the frame, fix the motor directly to the ground using screws suitable for the
type of floor (not included). Drawings 41-4.2.
In case of using the additional plate Ref. PLAK8700, fix the plate to the ground and
then fix the motor to the plate using the supplied screws that allow you to adjust the
exact final position with respect to the rack. It is recommended to use screws to posi-
tion the motor in the high position. Figure 4.3.
Over time, the progress of the structure tends to decrease. It will then be possible to
adapt the motor correction downwards.
5) MANUAL EMERGENCY RELEASE
(See the drawings in section 5).
The key release system allows the gate to be operated manually.
Two release keys are provided.
Turn the key clockwise, pull the knob towards you. The gate can now be moved ma-
nually.
To re-lock the engine, close the release knob, turn the key counterclockwise, and
remove the key in the vertical position. drawing 5.1.
Note: the release system is only accessible from inside the property. It is recommen-
ded that you make sure you have secondary access.
DUCATI
INSTALLATION
WARNING
:
The gate must be equipped with mechanical stops that prevent the
gate from derailing, causing a risk of serious danger to the life of people or things.
WARNING
: I
n the absence of a mechanical stop, do not automate or manually operate the
gate. Call a specialist right away to bring the facility to a standard level. The manufacturer
declines all responsibility for damage caused by improper installation of unsuitable or
dangerous structures.
PREPARATIONS BEFORE INSTALLATION
Motorization operated by a high voltage sector: A certified electrician must prepare
the 230V 50Hz (or 110V 60H) power supply line with cable outlet at the point where
the motor will be earthed (procedure not necessary in case of motorization from solar
panel).
The surface on which the engine will be fixed to the ground must be perfectly smooth
and flat. It is advisable to arrange a higher floor from the ground to avoid possible
water infiltration, for example a masonry, concrete or iron base. It is also advisable to
add the plate Ref. PLAK 7800 as an option, which allows a better adjustment of the
final position of the motor with respect to the rack. This optional accessory facilitates
the correction of the position that may be necessary over time or in relation to the
change of season due to the expansion of the materials in relation to the temperature.
The height of the surface where the motor is to be fixed must also be studied in rela-
tion to the position of the frame that will be installed on the gate.
Prepare sheaths for the passage of the accessory connection cables (flashing light,
key selector and possible set of photocells, external receiver).
3) ENGINE POSITIONING: RIGHT OR LEFT
(See the drawings in section 3, page 6).
The motor must be installed parallel to the gate. Inside the property at the level of the
column corresponding to the side on which the gate opens.
It is important to calculate the mounting position of the motor over the distances indi-
cated within the limits of drawing 4.2, on page 6.0.
MOTOR CABLE CONNECTION
depending on the direction of movement of the gate:
gate that opens to the right or opens to the left (seen from inside the property).
The motor is designed for a STANDARD opening of the gate on the right (seen from
inside the property). Illustration 3.2.
If the gate opens to the left it is necessary to reverse the polarity of the red and blue
