DTI Dyna Technology WINPOWER DE20I4, Инструкция по установке и эксплуатации

Страница: 11 / 24

2080-10 60708-151
Minimum Conductor Sizes between the Generator and the load.
Based on wire type and temperature rating. Wire has been
derated for 40
o
C ambient temperatures.
Cu Conductor Al Conductor
C/B Wire Temperature Rating
kW Voltage PH Amp 750C 900C 750C 900C
20 120/240 1 85 #3 AWG #4 AWG #1 AWG #2 AWG
20 120/208 3 70 #4 AWG #6 AWG #3 AWG #4 AWG
20 120/240 3 60 #4 AWG #6 AWG #3 AWG #4 AWG
20 277/480 3 30 #8 AWG #8 AWG #8 AWG #8 AWG
30 120/240 1 125 1/0 AWG #1 AWG 3/0 AWG 2/0 AWG
30 120/208 3 100 #2 AWG #3 AWG 1/0 AWG #1 AWG
30 120/240 3 90 #2 AWG #3 AWG 1/0 AWG #2 AWG
30 277/480 3 45 #6 AWG #8 AWG #4 AWG #6 AWG
45 120/240 1 175 3/0 AWG 2/0 AWG 250 MCM 4/0 AWG
45 120/208 3 150 2/0 AWG 1/0 AWG 3/0 AWG 2/0 AWG
45 120/240 3 125 1/0 AWG #1 AWG 3/0 AWG 2/0 AWG
45 277/480 3 60 #4 AWG #6 AWG #3 AWG #4 AWG
65 120/240 1 250 300 MCM 250 MCM 500 MCM 350 MCM
65 120/208 3 225 250 MCM 4/0 AWG 400 MCM 300 MCM
65 120/240 3 200 4/0 AWG 3/0 AWG 300 MCM 250 MCM
65 277/480 3 100 #2 AWG #3 AWG 1/0 AWG #1 AWG
For additional information on wire sizing refer to table 310-16 of
the National Electrical Code ANSI/NFPA 70..
For additional information on wire sizing refer to table 310-16 of
the National Electrical Code ANSI/NFPA 70.
Ground Lug , These ground lugs are bonded to ground and are
provided for you to connect your ground wire from the transfer
switch to. The lugs on the 65 kW will handle wire sizes #6 AWG to
300 MCM and should be torqued to 250 in. lbs. The lugs on the
20 through 45 kW will accommodate #10 AWG to 2/0 AWG and
should be torqued to 200 in. lbs.
*************
***** WARNING *****
*************
PERSONAL DANGER - These unit are shipped with a
FLOATING NEUTRAL. If you not connecting to an existing
power system you must install a neutral to ground bond in
the generator connection box. If your system already has a
neutral to ground bond then you must run a separate ground
lead to that location. For additional questions refer to the
current National Electric Code on grounding.
*************
***** WARNING *****
*************
EQUIPMENT DAMAGE - When installing a Three Phase 240
volt system be sure you know which lead is the high voltage
“wild” leg (208 Volt line to neutral). The generator normally
carries the high voltage on the G2 lead.
All wires should be installed in flexible conduit. ( A knockout
covered by a rubber plug is provided in the control box).
ENGINE CONTROL PANEL
LAYOUT DSE702
A - 2 AMP FUSE This fuse supplies the DSE702 controller
120 Volt AC. This tells the controller that the unit is running.
(Replacement AGC-2A-250V)
B - 2 AMP FUSE -This fuse is in the 12 volt DC power supply for
the DSE702 controller circuitry on the board. It also supplies the
voltage for the two or three control relay in the control cabinet.
(Replacement AGC-2A-250V)
C - 25 AMP FUSE - This fuse provides the 12 volt DC voltage
for the relay controlling the starting, fuel, and glow plugs.
(Replacement AGC-25A-250V)
D - DSE702 Start Controller - See Description Later
A
B
D
C