DriSteem STS 100C Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 64

background image

28

STS INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Wiring

INSTALLATION

Brown or black, top probe rod (full water condition)

Orange or white, middle probe rod (reﬁ ll water condition)

Violet or red, bottom probe rod: Low water condition,

tap/softened water

TOP

MID

LOW

WIRING DIAGRAM LOCATIONS

•

Ladder style wiring diagrams (located inside control cabinet door)
show power, control, and humidiﬁ er-to-control-cabinet interconnection
requirements.

•

External connections diagrams (located inside control cabinet door) show
connection points to the microprocessor-based controller and wire terminals
for the following external safety and control devices: airﬂ ow proving
switches, high limits, transmitters, or humidistats.

All wiring must be in accordance with all governing codes and with STS wiring
diagrams.

ELECTRICAL INSTALLATION

Wiring and branch circuit protection is provided by the installer per the
National Electrical Code (NEC) or in Europe, IEC 60364. For power supply
and machine ground connections, size the wire using the 75 °C wiring table,
per the NEC (or IEC 60364). Then use copper conductors rated for a 105 °C
environment. The wiring from the control cabinet to the humidiﬁ er must be
rated for 105 °C.

All STS humidiﬁ ers have a 120V, single phase electrical supply for North
America or 230V, single phase electrical supply for Europe. Verify current
characteristics and capacity requirements against those listed on the name
plate.

WIRING REQUIREMENTS

The length of wire from the control cabinet to the humidiﬁ er must not exceed
50' (15 m). Run control wiring in dedicated, earthed, metal conduit or cable
trays or trunking that is separated from the building’s power wiring.

Notes:

• See Outdoor Enclosure electrical

speciﬁ cations in Table 13-2.

• Damage caused by chloride corrosion is not

covered by your DriSteem warranty.

CAUTION

Damage from debris

When drilling penetrations in the
control cabinet, protect all internal
components from debris, and vacuum
out the control cabinet when ﬁ nished.
Failure to comply with this directive
can damage sensitive electronic
com po nents, cause erratic operation
or failure, and void your DriSteem
warranty.

WARNING

Electric shock hazard

Only qualiﬁ ed electrical personnel
should perform ﬁ eld wiring installation
procedures. Improper wiring or contact
with energized circuits can cause
property damage, severe personal
injury, or death as a result of electric
shock and/or ﬁ re.

Do not open control cabinet until
electrical power is disconnected.

FIGURE 28-1: WATER LEVEL CONTROL WIRING FOR VAPOR-LOGIC

«
...
30
31
32
33
34
...
»

Содержание STS 100C

































































Отзывы:

Нет отзывов

Похожие инструкции для STS 100C

Бренд: DanVex Страницы: 12

Бренд: Lanaform Страницы: 112

cont21200810247

Бренд: Conti+ Страницы: 12

Бренд: Gardner Denver Страницы: 36

Бренд: Ariston Страницы: 72

Бренд: Aircare Страницы: 36

All Climate LAD250

Бренд: Breville Страницы: 16

Бренд: Comfort Zone Страницы: 6

Бренд: Crane Страницы: 15

Бренд: Vapac Страницы: 10

Бренд: Arlec Страницы: 8

Бренд: Sharper Image Страницы: 4

easy dry compact

Бренд: SOLIS Страницы: 32

Бренд: Dantherm Страницы: 13

Бренд: KAESER Страницы: 20

Бренд: Qlima Страницы: 204

Бренд: DanVex Страницы: 12

Бренд: Easy@Home Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды