DriSteem STS 100C Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 64

background image

15

STS INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

DC-1478

B

Standard steam outlet (exits enclosure here)

Intake ven ti la tion fan

D

C

Pipe chase extending 1" (25 mm) above enclosure ﬂ oor

STS hu mid i ﬁ er

Elec tri cal and cleanout access
door

Control panel heater

Control panel

Enclosure drain

E

Optional steam outlet
(exits enclosure through pipe chase)

Valve access door:
• Models 25-100 have one access door
• Models 200-800 have two access doors

Intake ventilation fan

Valve section heater

Valve access door

J

H

Outdoor Enclosure

INSTALLATION

F

MOUNTING

• Outdoor Enclosure must be level and positioned with enough clearance to

open access doors.

• Verify that position of pad or curb properly supports Outdoor Enclosure,

and that support structure dimensions coincide with unit dimensions.

• Locate unit so air intakes are not close to exhaust fan outlets, gasoline

storage, or other contaminants that could potentially cause dangerous
situations. Using or storing gasoline or other ﬂ ammable vapors and liquids
in open containers in vicinity of Outdoor Enclosure is hazardous.

• When located on roof, Outdoor Enclosure air intakes must be a minimum

of 14" (356 mm) above roof to prevent intake of snow or splashed rain.
Position Outdoor Enclosure so prevailing winds do not blow into air intakes.

• Remove all shipping brackets and other packaging prior to installing the

unit.

• During transit, unloading, and setting of the unit, bolts and nuts may have

become loosened. Check that all nuts are tightened.

Important note about STS Outdoor
Enclosure installation

• Install a riser trap in the branch line leading

to the humidiﬁ er.

• The preferred location for the STS steam

control valve is inside the Outdoor Enclosure.
If one of these valves must be located inside
the building, it must be located within 6'
(1.8 m) of the humidiﬁ er to reduce pressure
drop.

FIGURE 15-1: STS OUTDOOR ENCLOSURE, TOP VIEW

«
...
17
18
19
20
21
...
»

Содержание STS 100C

































































Отзывы:

Нет отзывов

Похожие инструкции для STS 100C

Бренд: EIPL Страницы: 12

Бренд: Santa Fe Страницы: 15

Calorex DH75 Series

Бренд: Dantherm Страницы: 19

Бренд: Amana Страницы: 32

Бренд: German pool Страницы: 16

Бренд: Clean Air Optima Страницы: 134

Бренд: RDZ Страницы: 12

CoolMist VUL565E

Бренд: Vicks Страницы: 45

Бренд: Tesla Страницы: 74

Бренд: Topcom Страницы: 92

Herrmidifier G100

Бренд: Trion Страницы: 2

Бренд: Trion Страницы: 2

23-11-2233N-009

Бренд: Maytag Страницы: 16

Бренд: Healthy Climate Solutions Страницы: 4

Бренд: Healthy Climate Страницы: 4

Бренд: DriSteem Страницы: 28

Бренд: DriSteem Страницы: 32

Бренд: Dri-Eaz Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды