DriSteem STS 100C Скачать руководство пользователя страница 23

Страница: 23 / 64

STS INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

INSTALLATION

STS with RO/DI water option and manual drain

has a pipe thread ﬁ tting on the

drain valve and on the skim/overﬂ ow ﬁ tting. Prior to dumping into a drain, the
installer needs to connect the drain and skim/overﬂ ow, provide a water seal of
height H1 (see Table 22-1), and pipe.

DRAIN CONNECTION

Note: This section applies to all tap/softened water STS models and all STS

models with the RO/DI and auto drain options.

The installer should install a water seal of height H1 (see Table 22-1).

The drain connection provided is a ProBite

™

quick connection. Connect as

follows:

1. See Warning and Caution at right.

2. Cut drain line to length for insertion depth shown below for your ProBite

connector size. Cut must be clean and smooth.

3. Ream and de-burr drain line before connecting to ProBite connection.

Make sure drain line is clean, round, and free from damage.

4. Mark insertion depth on drain line according to table below for your

ProBite connection size.

5. Push drain line into ProBite connection to insertion depth marked in Step 4.

OM-7644

WARNING

Do not insert fi ngers or any body part
into ProBite connection openings

Insert only piping into ProBite
connection. Inserting ﬁ ngers or any
body part could require emergency
medical attention for removal.

CAUTION

ProBite installation precautions

To avoid damage to the ProBite
connection:

• In addition to DriSteem drain

piping material requirements on
the facing page, ProBite ﬁ ttings are
compatible only with copper, PEX,
CPVC or stainless steel.

• Do not solder within 10" (250 mm)

of the ProBite connection.

• Do not use heat or glue when

installing the ProBite connection.

ProBite ﬁ tting

Drain line

Connector

size

Insertion depth (D)

in.

3/4"

27 mm

33 mm

Piping: Drain

FIGURE 19-1: DRAIN CONNECTION (ALL MODELS EXCEPT STS WITH RO/DI
WATER OPTION AND MANUAL DRAIN)

Содержание STS 100C

































































Результаты поиска

Содержание STS 100C

Отзывы:

Похожие инструкции для STS 100C

Бренды по названию

Популярные бренды

DriSteem STS 100C, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание STS 100C

Отзывы:

Похожие инструкции для STS 100C

Бренды по названию

Популярные бренды