DriSteem STS 100C Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 64

background image

17

STS INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Outdoor Enclosure

INSTALLATION

MOUNTING (CONTINUED)

• Keypad/display with standard 5' (1.5 m) cable ships mounted to subpanel

in Outdoor Enclosure. Keypad/display must not come in contact with strip
heaters or block intake ventilation hood.

• If constant monitoring of unit is desired, or if unit is located in a severe

climate, a remote-mount keypad/display should be installed. Additional
cable lengths up to 500 feet (152 m) are available as an option for this
mounting conﬁ guration.

• 16-gauge galvanized steel curbs (optional) are shipped unassembled for

ease of transporting to roof; they include all hardware for bolt-together
assembly, and all holes are matched before leaving factory. Curb must
be a minimum of 14" (356 mm) high. One 2" × 1/2" closed-cell curb
gasket with adhesive on one side is supplied with hardware. Gasket must
be installed between top of curb and base surface of Outdoor Enclosure
to prevent moisture from leaking into building from driving rain or melting
snow. Installation drawing is included.

• All piping from humidiﬁ er to steam outlet is stainless steel pipe. Depending

on the application, tubing or DriSteem steam hose is recommended for
interconnecting piping from steam outlet to dispersion assembly.

STS OUTDOOR ENCLOSURE SEQUENCE
OF OPERATION

• Power is applied to Outdoor Enclosure:
•

If ambient temperature in enclosure is below
50 °F (10 °C), the strip heaters power up.
Strip heaters remain on until enclosure
reaches 50 °F (10 °C) to ensure that
enclosure temperature does not drop below
the freezing point.

•

When there is no call for humidity, an
aquastat maintains tank temperature at
the factory default of 70 °F (21 °C). This
temperature can be reset in the ﬁ eld to be
from 40 to 180 °F (4 to 82 °C).

•

When the ambient temperature in the
enclosure reaches 85 °F (29 °C), two
ventilation fans turn on to cool the electronic
components. A high limit is also provided
to power down the STS if the enclosure
temperature reaches 150 °F (66 °C). In
a high limit situation, the ventilation fans
continue to run and once the enclosure
temperature falls below 130 °F (54 °C), the
STS automatically resumes normal operation.

•

A normally open drain valve is provided on
the STS Outdoor Enclosure to drain the tank
in the event of a power loss.

OM-7464
mc_012611_1545

OM-955

Left side:
36"
(914 mm)

Top:
Keep open

Back:
12"
(305 mm)

Right side:
24"
(610 mm)

Front:
36"
(914 mm)

mc_012611_1546

Steam piping

Roof surface

Curb

Water piping

Remote Vapor-logic keypad

Electrical con nec tions

Drain piping

Humidiﬁ er in Outdoor Enclosure

FIGURE 17-1: TYPICAL ROOFTOP INSTALLATION OVERVIEW

FIGURE 17-2:
OUTDOOR ENCLOSURE CLEARANCES

«
...
19
20
21
22
23
...
»

Содержание STS 100C

































































Отзывы:

Нет отзывов

Похожие инструкции для STS 100C

Бренд: Easylife Страницы: 3

Бренд: Ultra-air Страницы: 20

Бренд: TaoTronics Страницы: 3

Бренд: Respironics Страницы: 47

Бренд: Goldair Страницы: 5

Бренд: Goldair Страницы: 9

Бренд: PLANTA Страницы: 30

Бренд: Vapac Страницы: 10

Бренд: Magnavox Страницы: 6

Бренд: Romus Страницы: 20

Бренд: HUMIDEW Страницы: 6

Бренд: Nortec Страницы: 20

Gas-fired Humidifier

Бренд: Nortec Страницы: 41

Бренд: Nortec Страницы: 54

Бренд: Nortec Страницы: 78

Бренд: Nortec Страницы: 76

Бренд: KDK Страницы: 52

Бренд: Vava Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды