Copyright 2002 Dri-Eaz Products, Inc.
4
7 Years on Housing: Repair or replace the DefendAir EX
housing for seven years from date of purchase. (United
States and Canada only.)
1 Year on Parts and Labor: Cover parts and labor costs of
repair on the DefendAir EX for a period of one year from the
date of purchase.
90 Days on Shipping: Cover shipping costs for the repair of
the DefendAir EX both to and from a Service Center for a
period of 90 days from the date of purchase.
LIMITATIONS: This warranty shall not extend to any prod-
ucts showing effects of misuse, accident damage, disassem-
bly, alteration, lack of proper maintenance, corrosive chemi-
cals, improper voltage, unauthorized repairs, use of other
than genuine parts and materials, fire, flood, normal wear
and tear, or any other causes beyond Dri-Eaz Products' con-
trol. The warranty obligation extends only to the repairs or
replacement of parts found, upon Dri-Eaz Products'
examination, to be defective. The foregoing constitutes the
entire warranty and no other warranty, liability, contingency
or responsibility, direct, indirect, consequential or in any way
connected with the sale or operation of products is
expressed or implied.
TO RECEIVE WARRANTY SERVICE: You must write or call
for a Return Authorization. To request an RMA, contact the
Dri-Eaz Service Department or visit www.dri-eaz.com. You
must have the serial number available. The Dri-Eaz Service
Department must authorize all costs, including shipping, for
any Service Centers worldwide. Please direct questions to
an authorized distributor, or to Dri-Eaz at (360) 757-7776,
extension 238.
SPECIFICATIONS
MODEL
DefendAir EX
Model Number
F258-230v UK
Voltage
230V
Frequency
50Hz
Power Required
1.0 amps
Dimensions
99 x 58 x 48 cm (39" x 23" x 19")
Use Weight
22 kg (49 lb)
Ship Weight
26 kg (57 lb)
Minimum CFM Rating
170 CMH (100 CFM)
Maximum CFM Rating
715 CMH (421 CFM)
Maximum CFM Rating (Free Air)
1386 CMH (816 CFM)
Blower Type
Motorized Impeller
Filter System
Up to 4-Stage: 3 Pre-f High Efficiency Primary Filter
Primary Filter
High Efficiency; filter media meets HEPA standards (99.97% at 0.3 microns) when tested
according to IES-RP-CC001.3; capable of 99.5% at 0.3 microns when installed in unit.
Pre-filter Dimensions
40.6 x 40.6 x 2.5 cm (16" x 16" x 1")
Housing Material
Thermoformed ABS
System Indicator Lights
Two (2): Pre-Filter Change and Primary Filter Change
Handle
Yes
Wheels
Yes
Safety Listings
CE
Specifications are subject to change without notice. Some values are approximate.
TROUBLESHOOTING
In COLUMN 3,
"FS" or Field Solutions
can be handled by the technician in the field. Others solutions should be handled by a repair technician –
an
"AST" or Authorized Service Technician
.
WARNING
: All the service procedures below should be executed with the power turned off, i.e. unplugged.
PROBLEM
CAUSE
See Above
SOLUTION
No power to machine
FS
Plug in the unit; check power at outlet
Switch not turned on
FS
Turn on the switch
No power to outlet
FS
Reset circuit breaker/CFGI
Defective power cord
AST
Replace power cord
Unit does not operate
Tripped motor thermal overload
FS
Turn unit off; wait 30 minutes then restart
Pre-filters are full
FS
Replace the pre-filters; refer to Maintenance section
Pre-Filter Change
light illuminated
Air intake restricted
FS
Eliminate bends/kinks in ducting, or remove ducting
Primary Filter Change
light illuminated
Primary filter is full
FS
Replace primary filter; refer to Maintenance section
Obstructed blower
FS
Remove obstruction
Loose blower wheel set screw
FS
Tighten set screw
Loose or broken wire
AST
Replace broken wire
Blower wheel not turning
Burned-out fan motor
AST
Replace fan motor
FOR PARTS AND SERVICE CALL YOUR LOCAL DISTRIBUTOR,
or the Dri-Eaz Service Department at (360) 757-7776
