Dräger Vamos Скачать руководство пользователя страница 29

Страница: 29 / 52

Operation in Measurement Mode

Operating Ins

tructions V

amos, 1

. US ed.

Selecting parameters to measure

Calibration

Selecting parameters to measure

Monitoring and presentation of anesthetic agents, N

O, CO

values and SpO

, Pulse values can be switched on and off.

The default for both settings on power-up is »

«.

To set:

●

Turn or press dial knob to select main menu.

●

Turn dial knob to select »

Param.

« parameter.

●

Press dial knob to open the parameter menu.

●

Turn dial knob to select setting for gas measurement
parameters.

●

Press dial knob to confirm setting.
The setting is marked with an arrow.

●

Turn dial knob to select setting for SpO

and Pulse

measurement.

●

Press dial knob to confirm setting.
The setting is marked with an arrow.

●

Press dial knob to return to the main menu.

●

Press dial knob again to return to the measurement
display.

If a parameter is switched off, the respective values are
replaced by "

". If the gases measurement is switched off,

the ﬁeld for the CO

-curve shows "

" in its center.

Calibration

SpO

measurement does not need to be calibrated.

Gas measurement is calibrated every 2 hours by the monitor.
During calibration, which lasts approximately 30 seconds, the
reading »

CAL

« appears in place of the gas measurement

values.

Gas measurement calibration may also be started manually
from the main menu:

●

Turn or press dial knob to select main menu.

●

Turn dial knob to select »

Cal

« in the main menu.

●

Press dial knob to confirm.

The device calibrates automatically; the next automatic
calibration is carried out again after 2 hours.

Gases

off

Hal
[%]

N2O
[%]

CO2
[%]

[1/min]

[%]

SpO2

Pulse

110

Param.

0.6

0.1

0.0

4.5

off

SpO2

exit

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Vamos





















































Результаты поиска

Содержание Vamos

Отзывы:

Похожие инструкции для Vamos

Бренды по названию

Популярные бренды

Dräger Vamos, Руководство по эксплуатации

Результаты поиска

Содержание Vamos

Отзывы:

Похожие инструкции для Vamos

Бренды по названию

Популярные бренды