Dormakaba RAC5 MFC Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 24

background image

12-2020

dormakaba Canada Inc. RAC5 MFC Installation Guide – PK3738 | 3

1 Introduction and Disclaimers

Please read and follow all directions carefully.

These instructions are designed for use by qualified installers or individuals with knowledge of common safety
practices and the competence to perform the steps described herein.

dormakaba Canada Inc. is not responsible for damage or malfunction due to incorrect installation.

Carefully inspect windows, doorframes, doors, etc. to ensure that the installation
procedures will not cause any damage. dormakaba Canada Inc.’s standard warranty does
not cover damages caused by installation.

Installation of card readers or other peripherals within elevators must only be done with

prior consultation of the elevator manufacturer. A technician from the elevator
manufacturer should always be present for installation. Do not connect to a receptacle
controlled by a switch.

If installing the RAC5 MFC in an elevator cage environment, or in proximity to any other equipment that may
generate high levels of electromagnetic interference, follow the installation requirements as indicated in Annex
C to prevent any operational instability.

The Table below outlines Access Control Levels as they pertain to certain Features.

Feature

Level

Destructive Attack Level

I

Line Security

I

Endurance Level

IV

Standby Power

I

Single Point Locking Device with Key Locks

I

RAC5 MFC Model #: T53-XXXXX

Firmware #: FW-516334-V 10.07.20.4

CAUTION

WARNING

«
...
2
3
4
5
6
...
»

Содержание RAC5 MFC

























Отзывы:

Нет отзывов

Похожие инструкции для RAC5 MFC

Бренд: MADRIX Страницы: 36

Бренд: Acclaim Lighting Страницы: 32

Бренд: Jeep Страницы: 19

Бренд: Kasco Страницы: 3

Бренд: C Prox Ltd Страницы: 5

Бренд: Häfele Страницы: 2

Бренд: Häfele Страницы: 24

Бренд: OMC Страницы: 18

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 2

FrameSaver 9120

Бренд: Paradyne Страницы: 20

VeriSafe VS2-NET

Бренд: Panduit Страницы: 6

Бренд: Rain Bird Страницы: 24

ESP-LXIVM Series

Бренд: Rain Bird Страницы: 16

Бренд: Rabe Страницы: 61

Бренд: Racal Instruments Страницы: 35

Бренд: Raypak Страницы: 24

Бренд: J+J Страницы: 91

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды