DoorKing 9150 Series, Инструкция по установке и эксплуатации

Страница: 38 / 54

9150-065-Y-12-20 34
ON ON
REVERSE
SENSITIVITY
EXIT
LOOP
FULL OPEN
DOORKING
4602-010
SW1
SW3
SW2
OPEN
TIMER
NC
NO
1
2
3
4
5
6
7
8
9
10
1
ON
2
3
4
ON
EXIT
LOOP
SW1
18
17
16
15
14
13
12
11
#10
9
8
7
6
5
4
3
2
1
ON
EXI
LOO
FULL OPEN
DOORKING
4602-010
S
NC
NO
1
2
3
4
5
6
7
8
9
10
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Open Beam-1
Common-2
Close Beam-3
Common-4
24 VAC-5
Common-6
Open Edge-7
Common-8
Close Edge-9
Common-10
Open Beam-1
Common-2
Close Beam-3
Common-4
24 VAC-5
Common-6
Open Edge-7
Common-8
Close Edge-9
Common-10
UL 325
Terminal
UL 325
Terminal
Main Terminal Main Terminal
UL 325
DIP-switches
1, 2 and 3 ON
1
ON
2
3
4
UL 325
DIP-switches
1, 2 and 3 ON
1
ON
2
3
4
Secondary
Operator
Primary
Operator
To Close Beam #3
To Open Edge #7
To Common #4
To Open Edge #7
To Open Beam #1
To Common #8
To Common #2
To Common #8
Fence
Gate
Close Beam
Open Edge
Open Edge
Fence
Gate
5.4 Bi-Parting Gates Wiring - Dual Gate Operators
Entrapment Protection Devices
for Bi-Parting Gates
• Separate power source for
photo sensor (See page 25).
Interconnection Cable
Sold separately from DoorKing.
Reverse loop lead-in
wires are wired in series.
When using Dual
Channel plug-in
loop detector.
Connect #4 to #10:
fully opens gates.
Open Beam Note:
If Open beam is
required for
entrapment
protection, #1
and #2 UL 325
terminals MUST
be wired in
parallel between
primary and
secondary
operators.
SW 2, switch 1
must be
OFF .
Plug into Primary Operator Exit Loop Port
Dual Channel
9409
Automatic
Exit Loop
Reverse
Loop
Reverse
Loop
LL OPE LL OP OPE
Secondar
y Operator
Yellow
24 Volt
Relay
Com
Purple
Brown
Yellow
Purple
Brown
Orange
Jumper Wire
Orange
Blue Red
Red
Gray
Blue
Gray
Green to
primary
operator
chassis
ground. Green to
secondary
operator
chassis
ground.
#3 Red Close Beam
#4 Gray Common
#7 Blue Open Edge
#4 Yellow
#5 Purple
#6 Brown
#18 Orange
Close Beam Red #3
Common Gray #4
Open Edge Blue #7
Yellow #4
Purple #5
Brown #6
Orange #18
Loop Lead-In Wires
N.O.
Com
Loop Detectors
3-Wire Receiver
(Fully Opens Gates)
Jumper Wire
250 mA max.
4-wire receiver wiring,
see page 32.
ON
1
2
345678
SW 2
LL OPEN LL OP OPEN
Primar
y Operator
• Requires AC power to each operator.
• Both operator DIP-switches must be set.
• Connect normal opening device, auxiliary
devices and loops to the primary operator only .
• Connect FIRE DEPT
device to Both
operators.
UL 325 Terminal
Primar
y Operator
Secondar
y Operator
Main Terminal
Reflector
Main terminal #3 AND UL 325
terminal #5 Note:
Exceeding 250 mA of power from
either of these terminals may cause the
circuit board transformer to overheat,
causing intermittent problems.
Open Beam Open Beam
See pages 2 and 26 for gate
gap information.
To Open Beam #1
To Common #2
Type of wiring to be used on ALL
external devices:
A)
Type CL2 , CL2P , CL2R , or CL2X .
B) Other cable with equivalent or
better electrical, mechanical, and
flammability ratings.