DOGA DPC Touch Скачать руководство пользователя

Страница: 20 / 36

DPC Touch User Manual

7.4

Outputs

Activate desired outputs by selecting corresponding check boxes. Select required output type from
the list.

Non-assigned outputs can be used for Logical Out steps.

Duration of impulse signals is 100 ms.

Each output function can be assigned to multiple outputs.

Output name

Function description

Signal type

Fastening OK

Signal is provided after successful fastening operation.

Impulse

Fastening NG

Signal is provided after a fastening operation completed with
errors.

Impulse

Step OK

Signal is provided after successful completion of a step.

Impulse

Step NG

Signal is provided after if a step was interrupted or
completed with missing screws.

Impulse

Tool Enable

Signal is provided to enable the tool (when position is OK)

Continuous

Tool Disable

Signal is provided to lock the tool (when position is NOK or
during alarm mode)

Continuous

D_RUN

Signal is provided when the tool is running (D_Motor_Run
input has to be connected)

Continuous

D_TORQUE

Signal is provided when Fastening OK signal is received from
the tool (D_Fastening_OK input has to be connected)

Impulse

D_RESET

Signal is provided when reset was made (manually,
automatically or via I/O)

Impulse

Torque Select 1-8

Signals to select fastening presets on the tool in binary or
direct logic (see the table below). Logic is selected in
operating settings.

Continuous

Job OK

Signal is provided after successful completion of a job.

Impulse

Job NG

Signal is provided after if a job was interrupted or completed
with missing screws.

Impulse

System Ready

Signal is provided when the controller is in operating mode
and ready for selection of jobs. Once a job is started the
signal drops down.

Continuous

Alarm

Signal is provided when the controller is in Alarm mode

Continuous

The table below shows the relation between Torque select signals and Preset number in direct logic.

Pset number Torque select 1 Torque select 2 Torque select 3

…

Torque select 8

…

NOTE: See Input

’

s settings for binary logic example.

Содержание DPC Touch





































Результаты поиска

Содержание DPC Touch

Отзывы:

Похожие инструкции для DPC Touch

Бренды по названию

Популярные бренды

DOGA DPC Touch, Инструкция по эксплуатации

Результаты поиска

Содержание DPC Touch

Отзывы:

Похожие инструкции для DPC Touch

Бренды по названию

Популярные бренды